Walksnail 1S Avatar Mini HD Camera Mount for BetaFPV Canopy II (Meteor65/75 Pro II O4)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
This TPU mount allows you to adapt the Walksnail Avatar HD Nano Camera V3 (not Lite) into the BetaFPV Canopy II.
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 18
- Wydruki
- 0
- Wyświetlenia
- 111
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- RC & Robotics
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Walksnail Avatar HD Nano Camera Mount (TPU Cradle) for BetaFPV Canopy II
This TPU mount allows you to adapt the Walksnail Avatar HD Nano Camera V3 (standard 14x14 mm 1S camera, not the Lite version) into the BetaFPV Canopy II (the stock canopy used on the Meteor65 Pro II, Meteor75 Pro II, and DJI O4 Lite whoop setups).
Why?
The BetaFPV Canopy II comes designed specifically for the DJI O4 Lite camera mount or standard micro camera configurations. While the canopy bay can physically fit the thinner Walksnail 1S Lite camera using side adapters, the Walksnail Avatar HD Nano V3 (standard 1S / Mini 1S camera, 14×14 mm body) presents two major issues:
Width Constraint: At 14 mm wide, the Nano V3 camera completely fills the canopy bay from wall to wall. Any traditional side-mounting plates or adapters add 1–2 mm of thickness, making it physically impossible to slide the camera inside.
Mounting Hole Mismatch: The Walksnail Nano V3 uses center side pins, whereas the Canopy II features arc slots designed for top/bottom mounting screws.
My Solution: TPU Cradle
Instead of mounting to the camera's side screw holes or drilling into the canopy, this custom TPU cradle (inspired by the DJI O4 mount that is shipped by BetaFPV) grips the camera body across its top, bottom, front, and rear while making direct use of the canopy's stock screw slots.
In case you do prefer drilling for a less-crowded canopy, I've got a drill jig for this exact setup (it was my first solution before the camera mount!)
Key Features:
Zero-Drilling Installation: Mounts directly using the stock BetaFPV M1.4 canopy screws along the existing side arc slots.
Side-Slide Entry: Features an open side slot (9.7 mm) for the lens and a bottom-rear cable channel. You can slide the camera inside with the camera cable attached—no desoldering or unhooking required!
Protected Lens & Solid Pillars: The front frame features a 9.7 mm collar and reinforced 2.05+ mm side pillars to absorb impact during forward crashes.
Blind Ear Pockets: Recesses on the inside accommodate the camera’s side screw-hole ears (7.5 mm body depth / 9.0 mm including ears) without breaking the outer pillar wall or adding side bulk.
D-Profile Nose: Rounded front profile matches the inner contours of the Canopy II for maximum tilt clearance.
Enclosed Canopy Retention: Once inserted into the cradle and screwed into the canopy, the outer canopy wall seals the open side, keeping the camera securely locked in place.
Recommended Print Settings
Material: TPU (95A recommended for best balance of flex and crash absorption).
Orientation: Print flat on its side (the closed side face down on the build plate). The included print profile is already in this orientation.
Supports: None required. When printed on its side, all walls, flaps, and slots print vertically. The 9.7 mm lens window prints cleanly without internal supports.
Walls & Infill: Set 4+ wall loops (perimeters) so thin sections print as solid TPU.
Layer Height: 0.8mm
Layer Speeds:
(You can probably get away without reducing all of these speeds, but in my case I found quality/rigidity seriously suffered so I slowed everything down; I use a Bambu Lab A1 printer)First Layer: 30mm/s
Slow down for overhangs
Outer Walls: 30mm/s
Inner Walls: 40mm/s
First Layer (Optional): Enable Elephant Foot Compensation so the first layer squish doesn't exceed the tight 13.8 mm bay clearance.
Assembly Instructions & Screw Notes
Insert Camera: Slide the camera in from the open side, guiding the lens into the front window while allowing the cable to slide along the rear bottom channel. Push until the far side ear seats into its blind pocket.
Mount to Canopy: Place the assembly into the Canopy II bay. The canopy's side walls will enclose the open side.
Fastening Screws: Drive the stock BetaFPV M1.4 canopy screws directly into the printed 1.3 mm pilot holes. No dremeling or pre-threading needed—the self-tapping M1.4 screws will cut their own threads straight into the TPU as you tighten them down.