Paper Towel Dispenser Key – Ersatzschlüssel für Handtuchspender (modular)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Two-part replacement key for paper towel dispensers with a swappable pin insert (~8 mm spacing included). Handy 95 mm le
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 0
- Wydruki
- 0
- Wyświetlenia
- 14
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Bathroom
- Licencja
- Creative Commons — Attribution — Noncommercial
🇬🇧 English version below
🇩🇪 Deutsch
Schlüssel schon wieder weg? Kennen wir! 😅
Der Originalschlüssel für Papier-Handtuchspender hat die nervige Angewohnheit, genau dann zu verschwinden, wenn der Spender leer ist. Dieser Ersatzschlüssel ist schnell gedruckt und rettet Dich vor dem Aufhebeln mit Schraubendreher oder Kugelschreiber.
Ideal für Hausmeister, Reinigungskräfte, Werkstatt, Büro, Vereinsheim, Feuerwehrgerätehaus, Schule oder überall, wo ein Handtuchspender an der Wand hängt.
Der Schlüssel ist zweiteilig aufgebaut: Griff und Pin-Einsatz werden getrennt gedruckt und dann zusammengesteckt. Das sorgt für ein sauberes Druckbild und stabile Pins, weil jedes Teil in seiner optimalen Ausrichtung gedruckt werden kann.
Und das Beste: Der Einsatz ist austauschbar. Passt der Pinabstand bei Deinem Spender nicht, tauschst Du einfach nur den kleinen Einsatz aus, der Griff bleibt derselbe. So lassen sich auch andere Spendermodelle abdecken.
Mit 95 mm Länge liegt er gut in der Hand und verschwindet nicht so leicht in der Hosentasche. Unten ist eine Bohrung für eine Schnur, einen Schlüsselring oder ein Lanyard, damit er diesmal auch da bleibt, wo er hingehört. Die Aufschrift „Handtuchspender” sorgt dafür, dass jeder weiß, wofür der Schlüssel ist.
Wichtig: Vor dem Drucken kurz am Spender nachmessen, ob der Pinabstand passt (ca. 8 mm).
Maße:
Länge: 95 mm
2 Pins, Abstand ca. 8 mm
Zweiteilig: Griff + austauschbarer Pin-Einsatz
Bohrung für Schnur/Schlüsselring
Druckhinweise:
Gedruckt auf einem Prusa XL
Beide Teile einzeln drucken
Unkritisches Teil, Standardeinstellungen reichen völlig
Für mehr Stabilität an den Pins lieber PETG statt PLA
Tipp: Mach Dir gleich zwei oder drei, einer verschwindet garantiert wieder. 😉
Viel Spaß beim Nachdrucken, über Makes und Fotos freue ich mich! 🙂
🇬🇧 English
Lost the key again? We’ve all been there! 😅
The original key for paper towel dispensers has a nasty habit of disappearing exactly when the dispenser runs empty. This replacement key prints in no time and saves you from prying the cover open with a screwdriver or ballpoint pen.
Perfect for caretakers, cleaning staff, workshops, offices, clubhouses, fire stations, schools, or anywhere there’s a paper towel dispenser on the wall.
The key is designed in two parts: the handle and the pin insert are printed separately and then plugged together. This gives you a cleaner print and sturdier pins, since each part can be printed in its ideal orientation.
Best of all: the insert is swappable. If the pin spacing doesn’t match your dispenser, just swap out the small insert and keep the same handle. That way other dispenser models can be covered too.
At 95 mm long it sits comfortably in your hand and won’t get lost in your pocket as easily. There’s a hole at the bottom for a cord, key ring or lanyard, so this time it stays where it belongs. The German label “Handtuchspender” (“paper towel dispenser”) makes it clear to everyone what the key is for.
Important: Check your dispenser before printing to make sure the pin spacing fits (approx. 8 mm).
Dimensions:
Length: 95 mm
2 pins, approx. 8 mm spacing
Two-part design: handle + swappable pin insert
Hole for cord/key ring
Print settings:
Printed on a Prusa XL
Print both parts separately
Uncritical part, standard settings work just fine
For sturdier pins, PETG is a better choice than PLA
Tip: Print two or three right away, one of them is bound to go missing again. 😉
Happy printing – I’d love to see your makes! 🙂