Euro Coin Sorter – The Honest Item Sorter (Blockineer)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Printable companion to the Blockineer video #03 "The Item Sorter" (https://www.youtube.com/@blockineer – The game cheats
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 2
- Wydruki
- 0
- Wyświetlenia
- 22
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other 3D Objects for Learning
- Licencja
- Creative Commons — Attribution — Noncommercial
Euro Coin Sorter – The Honest Item Sorter (Blockineer)
Printable companion to the Blockineer video #03 "The Item Sorter" (https://www.youtube.com/@blockineer – The game cheats. We do the math.).
In Minecraft, hoppers sort items by counting them. This model is the honest, real-world version: it sorts euro coins by size. Pour a handful of coins onto the track – every coin drops into the first bin whose drop-through width is bigger than the coin. No electronics, no scanner, no label.
Status: designed and checked in CAD only (watertight meshes, fit and clearances calculated). Not test-printed yet – the tolerances are tight (see "The math"), expect to adjust the slot widths by ±0.1 mm for your printer.
Parts
File | What | Print orientation |
|---|---|---|
| Track plate with guide walls and 8 drop slots | flat, track side up |
| Stepped bin box with 8 bins (entry void + 8 bins) | upright as modelled |
| Parametric source (OpenSCAD, Customizer ready) | – |
No purchased parts. Glue (or tape) the plate onto the sloped top edge of the body so the slots sit above the bins.
Print settings (Bambu A1 / 0.4 mm nozzle)
Material PLA, layer 0.2 mm, 3 walls.
plate.stl: 100 % flat on the bed, no supports, 15 % infill. ≈ 25 g. Size 30.5 × 243.5 mm – diagonal placement not needed (bed 256 mm).
body.stl: 144.6 mm tall, 223.5 mm long – fits the A1 bed (256 × 256 × 256). No supports. Use 10 % gyroid infill, 2–3 walls. ≈ 150–190 g, about 10–14 h. Brim recommended.
Rough filament total ≈ 200 g.
Assembly
Print both parts.
Place
body.stlon a table, bins pointing up.Lay
plate.stlon the sloped top edges – walls of the plate on the outside, holes over the bins, the high end of the plate over the empty entry void.Glue with a few drops of CA glue (or two strips of tape) – leave the plate removable if you want to empty the bins.
Use
Put a mixed handful of 1 c – 2 € coins on the high end of the track, against the left guide wall.
The track is tilted 25° along and 3° sideways, so coins slide along the guide wall.
Coins fall into the bins in this order: 1 c · 2 c · 10 c · 5 c · 20 c · 1 € · 50 c · 2 €.
Lift the plate to empty the bins.
The math
Coin diameters (ECB): 1 c 16.25 · 2 c 18.75 · 10 c 19.75 · 5 c 21.25 · 20 c 22.25 · 1 € 23.25 · 50 c 24.25 · 2 € 25.75 mm.
The track has a fixed 5 mm rail under the guide wall and a second rail on the right whose inner edge steps away from the wall every bin. A coin lying against the wall spans 0 … d. It stays supported as long as it touches the right rail, i.e. while d > slot. It tips into the slot as soon as d < slot.
Bin | Coin | Ø (mm) | Slot edge from wall (mm) | Margin (mm) |
|---|---|---|---|---|
1 | 1 cent | 16.25 | 17.0 | 0.75 |
2 | 2 cent | 18.75 | 19.2 | 0.45 |
3 | 10 cent | 19.75 | 20.3 | 0.55 |
4 | 5 cent | 21.25 | 21.8 | 0.55 |
5 | 20 cent | 22.25 | 22.8 | 0.55 |
6 | 1 euro | 23.25 | 23.8 | 0.55 |
7 | 50 cent | 24.25 | 24.8 | 0.55 |
8 | 2 euro | 25.75 | 26.5 (open end) | 0.75 |
The tightest pair is 2 c → 10 c: 19.75 − 19.2 = 0.55 mm overlap. Print with 0.2 mm layers and check the slot widths with a caliper.
Watch out: the 5 cent coin (21.25 mm) is bigger than the 10 cent coin (19.75 mm), so the order in the bins is not the order of the values.
Slope: a coin slides when
tan(angle) > μ. At 25°, tan 25° = 0.47 – enough for PLA and coins (μ ≈ 0.3 – 0.4). If coins stall, raisetiltin the .scad to 28°.Slot length: each hole is
Ø + 3 mmlong so the coin drops through without jamming; between two holes a 3 mm bridge keeps the rails connected.
Compare with the video
The Minecraft sorter is ~2.5 items/s and never wrong because it counts items. This one sorts by size, by gravity, and is only as accurate as your slot widths: one measured number per coin, no scanner.
Customize
Open coin_sorter.scad in OpenSCAD and change dia and slot to sort other coins (US coins, tokens, washers). part = "assembly" shows both parts in place.
Credits
Design: Blockineer – https://www.youtube.com/@blockineer Coin dimensions: European Central Bank (ecb.europa.eu/euro/coins/common). Licence: CC BY-NC 4.0 – free for non-commercial use, please credit Blockineer.
