1 / 2
Euro Coin Sorter – The Honest Item Sorter (Blockineer) — image 1
1 / 2

Euro Coin Sorter – The Honest Item Sorter (Blockineer)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Printable companion to the Blockineer video #03 "The Item Sorter" (https://www.youtube.com/@blockineer – The game cheats

Rating
0 / 5
Likes
0
Downloads
2
Makes
0
Views
22
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial

Euro Coin Sorter – The Honest Item Sorter (Blockineer)

Printable companion to the Blockineer video #03 "The Item Sorter" (https://www.youtube.com/@blockineer – The game cheats. We do the math.).

In Minecraft, hoppers sort items by counting them. This model is the honest, real-world version: it sorts euro coins by size. Pour a handful of coins onto the track – every coin drops into the first bin whose drop-through width is bigger than the coin. No electronics, no scanner, no label.

Status: designed and checked in CAD only (watertight meshes, fit and clearances calculated). Not test-printed yet – the tolerances are tight (see "The math"), expect to adjust the slot widths by ±0.1 mm for your printer.

Parts

File

What

Print orientation

plate.stl

Track plate with guide walls and 8 drop slots

flat, track side up

body.stl

Stepped bin box with 8 bins (entry void + 8 bins)

upright as modelled

coin_sorter.scad

Parametric source (OpenSCAD, Customizer ready)

–

No purchased parts. Glue (or tape) the plate onto the sloped top edge of the body so the slots sit above the bins.

Print settings (Bambu A1 / 0.4 mm nozzle)

  • Material PLA, layer 0.2 mm, 3 walls.

  • plate.stl: 100 % flat on the bed, no supports, 15 % infill. ≈ 25 g. Size 30.5 × 243.5 mm – diagonal placement not needed (bed 256 mm).

  • body.stl: 144.6 mm tall, 223.5 mm long – fits the A1 bed (256 × 256 × 256). No supports. Use 10 % gyroid infill, 2–3 walls. ≈ 150–190 g, about 10–14 h. Brim recommended.

  • Rough filament total ≈ 200 g.

Assembly

  1. Print both parts.

  2. Place body.stl on a table, bins pointing up.

  3. Lay plate.stl on the sloped top edges – walls of the plate on the outside, holes over the bins, the high end of the plate over the empty entry void.

  4. Glue with a few drops of CA glue (or two strips of tape) – leave the plate removable if you want to empty the bins.

Use

  1. Put a mixed handful of 1 c – 2 € coins on the high end of the track, against the left guide wall.

  2. The track is tilted 25° along and 3° sideways, so coins slide along the guide wall.

  3. Coins fall into the bins in this order: 1 c · 2 c · 10 c · 5 c · 20 c · 1 € · 50 c · 2 €.

  4. Lift the plate to empty the bins.

The math

Coin diameters (ECB): 1 c 16.25 · 2 c 18.75 · 10 c 19.75 · 5 c 21.25 · 20 c 22.25 · 1 € 23.25 · 50 c 24.25 · 2 € 25.75 mm.

The track has a fixed 5 mm rail under the guide wall and a second rail on the right whose inner edge steps away from the wall every bin. A coin lying against the wall spans 0 … d. It stays supported as long as it touches the right rail, i.e. while d > slot. It tips into the slot as soon as d < slot.

Bin

Coin

Ø (mm)

Slot edge from wall (mm)

Margin (mm)

1

1 cent

16.25

17.0

0.75

2

2 cent

18.75

19.2

0.45

3

10 cent

19.75

20.3

0.55

4

5 cent

21.25

21.8

0.55

5

20 cent

22.25

22.8

0.55

6

1 euro

23.25

23.8

0.55

7

50 cent

24.25

24.8

0.55

8

2 euro

25.75

26.5 (open end)

0.75

  • The tightest pair is 2 c → 10 c: 19.75 − 19.2 = 0.55 mm overlap. Print with 0.2 mm layers and check the slot widths with a caliper.

  • Watch out: the 5 cent coin (21.25 mm) is bigger than the 10 cent coin (19.75 mm), so the order in the bins is not the order of the values.

  • Slope: a coin slides when tan(angle) > μ. At 25°, tan 25° = 0.47 – enough for PLA and coins (μ ≈ 0.3 – 0.4). If coins stall, raise tilt in the .scad to 28°.

  • Slot length: each hole is Ø + 3 mm long so the coin drops through without jamming; between two holes a 3 mm bridge keeps the rails connected.

Compare with the video

The Minecraft sorter is ~2.5 items/s and never wrong because it counts items. This one sorts by size, by gravity, and is only as accurate as your slot widths: one measured number per coin, no scanner.

Customize

Open coin_sorter.scad in OpenSCAD and change dia and slot to sort other coins (US coins, tokens, washers). part = "assembly" shows both parts in place.

Credits

Design: Blockineer – https://www.youtube.com/@blockineer Coin dimensions: European Central Bank (ecb.europa.eu/euro/coins/common). Licence: CC BY-NC 4.0 – free for non-commercial use, please credit Blockineer.