1 / 5
Lab Rax 1U 4x40mm Fan Panel (10" rack) – wide spacing + 5 grille styles — zdjęcie 1
1 / 5

Lab Rax 1U 4x40mm Fan Panel (10" rack) – wide spacing + 5 grille styles

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

4-fan remix of the Lab Rax 1U 40mm fan panel with wider spacing. Open version plus 5 grille styles: honeycomb & more.

Ocena
0 / 5
Polubienia
1
Pobrania
14
Wydruki
1
Wyświetlenia
43
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Computers
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Lab Rax 1U 4x40mm Fan Panel – Remix

This is a remix of the "1U 5x40mm Fan Panel for 10" Rack" by mklements, the designer of the Lab Rax 3D-printable 10" rack system. Original model: https://makerworld.com/en/models/1293794 – all credit for the original design goes to him.

What's changed

- 4 fans instead of 5

- Fans are spread evenly across the panel: 58 mm centre-to-centre (original 43.5 mm), leaving an 18 mm gap between fans

- Outer fans stay in the same position as the original

- NEW: 5 grille versions with built-in fan guards

- Panel size, Lab Rax rack holes, 38 mm fan openings, 4 mm fan screw holes (32 mm spacing) and thickness are unchanged

Files

- Open – no grille, maximum airflow

- Honeycomb – hexagon pattern, the classic tech look

- Rings – circles with a cross, like a standard metal fan guard

- Bars – clean horizontal slats

- Diamond mesh – fine diagonal grid, looks like perforated metal, keeps fingers and cables out best

- Turbine – spokes from a centre hub, looks great with RGB fans spinning behind it

Grilles are 1.6 mm thick and sit flush with the front face.

Airflow tip

Every grille blocks some airflow. Honeycomb, bars and turbine flow the most; diamond mesh the least. For small 40 mm fans, honeycomb or turbine are a good balance of looks and airflow.

Mount the panel low in the rack as intake (fans blowing in), with a 120 mm fan on top as exhaust. Warm air rises, so this works with the natural airflow. Check the small arrows on the fan housing for airflow direction.

What you need

- 4× 40 mm fans (40 x 40 x 10 mm). I used WINSINN 40 mm 5V RGB fans, 4-pack, hydraulic bearing, XH2.54 2-pin plug. Search for "40mm 5V RGB fan 4010 4-pack" on Amazon or AliExpress. A 5V USB version also exists.

- Fan screws: the self-tapping screws that come with the fans fit the 4 mm holes. Short M3 screws with nuts also work.

- Rack screws: same as the rest of your Lab Rax frame – M6 x 12 mm button head + M6 nuts (bolted version), or M6 x 10 mm into heat-set inserts (insert version).

Powering the fans

5V fans can run from a single USB port: all 4 together draw about 0.5 A. Connect them in parallel to a USB cable (red = +5V, black = GND), or use USB-to-XH2.54 adapter cables.

Print settings

- Orientation: front face flat on the bed – the grille prints as the first layers, so no supports or bridging are needed and you get a smooth bed texture on the front

- Supports: none

- Material: PLA+ or PETG (PETG if the rack runs warm)

- Layer height: 0.2 mm

- Walls: 3–4, infill 15–20%

License

Same as the original: CC BY-NC-SA 4.0 – non-commercial use only, share remixes under the same license, and credit mklements.

Tagi