1 / 11
Airbus A320 Standby ISIS Panel — zdjęcie 1
1 / 11

Airbus A320 Standby ISIS Panel

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

The standby ISIS Panel for an Airbus A320 home cockpit.

Ocena
0 / 5
Polubienia
0
Pobrania
3
Wydruki
0
Wyświetlenia
27
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Other Ideas
Licencja
Creative Commons — Attribution — Noncommercial

I am currently selling this panel as s kit with the PCB and components included. Send me a message if you are interested!

More and better pictures coming in a few weeks!

Introduction:

This is my relatively 1:1 Standby ISIS Panel designed to sit in front of an actual computer monitor and connect to my other panel. Since most MIPs use a bigger computer monitor behind the actual panel to show both ECAM screens and they usually extend outward to this module too, this is designed to sit in front of that monitor which will show the actual screen. This panel is also designed to connect to my other Terrain on ND panel and be controlled by it.

The panel uses a custom ordered PCB with only surface mounted components to make it as thin as possible, it extends maximum 2.6mm behind the MIP surface.

There are two versions of the front panel which use the same components and board, the difference is that one of them is thicker on the left side and designed to fit on smaller back monitors like the 19 inch monitors and the other one is the standard size. they use the same components and parts and are assembled in the same way.

Video Tutorial

A full video tutorial is on the way!

B.O.M (Bill Of Materials):

These are all the electronical and mechanical components you will need:

Qty.

Item

Link (Aliexpress)

4

M3x4mm Heat Set Inserts

https://www.aliexpress.com/item/1005008318533389.html

4

M3x5mm Socket Head Screws

https://www.aliexpress.com/item/4001260319198.html

1

M3x3mm Grub Screw

https://www.aliexpress.com/item/32982295134.html

1

EC11 Surface-Mounted Rotary Encoder

https://www.aliexpress.com/item/1005007274268638.html

1

JST-XH Surface Mounted Horizontal 9 pin header

https://www.aliexpress.com/item/1005009461785955.html

5

3x6x4.3mm Surface Mounted (SMT) Momentary Switches

https://www.aliexpress.com/item/1005003751795914.html

-

Some JST-XH housings and crimping contacts, I recommend a kit like this

https://www.aliexpress.com/item/1005012526878591.html

1

Custom Ordered ISIS PCB

Ordered from JLCPCB

Printing

You will need three different colored PLA filaments, a black and white. These can be any brand that you chose. And, you will need a lighter blue for the front frame, I use "Panchroma Matte Muted Blue".

For this panel there is only one print profile with a 0.2mm nozzle set. I highly recommend printing with a 0.2mm nozzle for better text quality and details. All you need to do is open the profile and all the parts and settings should already be loaded up. But here are some of the more important settings if you don't use the profile:

The visible multicolored objects (front panel face and buttons) are .3mf files with multiple parts per object. When you load them into your slicer you want to load them as one object with several parts. Next you want to set the color for each of the parts. In the objects tab (prusaslicer/orcaslicer/bambu studio) you will see all the parts and their names. Everything that is named "Text..." is the top white text so chose the white filament. The other parts are all either black or blue filament.

The front panel and buttons have ironing turned on and oriented so it goes from side to side for a smoother look. There are two versions of the knob availible, one is the "standard" version with a long shaft and normal tolerances, the other one has a much shorter shaft length. Since the encoder I use is very small and short, it might be easier to use the second knob.

There are two versions of the fornt panel, one is called the "19 inch version" which is thicker on the left side and therefore fits on smaller back monitors like 19 inch sizes without showing the edge of the screen. If you have a smaller monitor, use the smaller one, otherwise print the standard size one. They are assembled in the same way and use the same components.

The Rotary Knob is already included in the print profile, but you can find it here anyway:

PCB

I ordered my PCB from JLCPCB without any pre assembly on the factory, and soldered everything at home since it is such a simple board. You only need three components in total for the board. One surface mounted EC11 rotary encoder, five small pushbuttons and a JST-XH header. Since the board needs to be as compact and thin as possible all the components are surface mounted, no pins go through the actual board body. This also means that I wasn't able to fit any LEDs on the board and therefore it does not have any backlighting.

I have made a video on how to order the PCB and print the parts, however you can exclude most of the special settings since this panel is som simple:

Assembly

PCB

Start with the small pushbuttons. Using a bit of sticky-tack will greatly help in the assembly process. Use it to secure the buttons in their footprints, one at a time, and solder one of the pins. Using some tweezers while heating the pad will enable you to adjust the position very finely. Remove the sticky-tack and solder the other pad, repeat for all five buttons.

Do the same for the Encoder, make sure the orientation is right, three pins on one side and two on the other. Secure with tack, solder one pin, adjust and solder everything. And finally do the same with the JST header on the other side of the board. Secure, solder one pin, adjust and solder everything.

Main Panel

Start with the front panel, insert the four M3x4mm heat inserts using a soldering iron, into the four holes on the back of the front panel. Also insert the buttons into their slots in the frame in the correct slots (see pdf/picture).

Next you need to secure the panel to your actual MIP, this was desgned to fit the SimGuy MIP, but should fit most other 10mm thick ones like the SL3 MIP. Insert the panel from the front and insert the PCB from the back. In the four holes insert the four printed screw housing parts and into those the four screws and gently secure them. It is constructed this way to minimize the thickness and as to not scratch the screen behind it with the screws. the panel doesnt actually mount to the MIP, but simply "squeezes" it and holds on like that.

And finally mount the small knob using the M3 grub screw, this step might be hard since the encoder has such a short shaft, but it should still work and be clickable.

This panel connects via the 9 pin JST header to my other Terrain on ND panel which then communicates with the microcontroller and computer. You can of cpurse still use it seperately, just connect the pins directly to a microcontroller and flash everything as regular.

Software

Since this panel isn't deisgned to actually control and read the button presses itself you need the terrain panel or any other microcontroller, refer to that on how to set up the software (Mobiflight)

However, for the actual display, in any aircraft in Microsoft flight simulator if you hold the Right Alt Key the cusros will turn into a magnifying glass, by then clicking on a panel display, in this cas the ISIS display, it will "pop out" and be rendered in a seperate window. You can then drag this window around and resize it so it fits inside the panel. I also use an application called "MSFS Pop Out Panel manager" which automatically pops out the panel and positions them in the correct places.

Other Models

Check out my profile for my other models!

Tagi