1 / 11
Salt Strike v3 — zdjęcie 1
1 / 11

Salt Strike v3

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Upgraded and revised version of the Salt Strike. Larger compression cylinder, better flow, hopper fed system.

Ocena
5 / 5
Polubienia
9
Pobrania
30
Wydruki
0
Wyświetlenia
286
Oceny
1

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Other Gadgets
Licencja
Creative Commons — Attribution — Noncommercial

This is V3 of my Salt Strike bug blaster. This version has been upgraded almost every way i could think of. This one features a larger cylinder with FAR more air blasting power, hopper system totally negating the need to remove barrels and reload after several shots. and a Charging handle for quick reloads.

On this version the 2 body shells slide together in the middle, sanding to fit may be required it may not depending on your settings. The same quick change barrel system is on this version as well, its just intergrated into the front shell.  The hopper system is just a gravity hopper with a slider door. The door opens/closes by the handle on the back of the cylinder shell (pics shown). the slider for the salt will need a quick pass with 800 grit to remove layer lines and it with operate smoothly in the hole. Speaking of tolerances, everything was made to fit TIGHT, but not aggressively tight. if youre fighting to put the 2 body halves together, stop, file down the edges and try again. its made to be taken apart and parts replaced. theres no glue used in this model just friction fit. THAT BEING SAID, if you sand too much where the 2 halves meet the front will fly off every other shot. you want it tight but removeable.

Just like last versions you will need to hone out the cylinder with sandpaper and a drill. THE SLOWER YOU PRINT THE CYLINDER THE LESS POST WORK WILL BE NEEDED. I would also do .18 height with the cylinder and no faster than 60 outer wall speed. i started with 120 and went to 1000 grit, PETG seems to be working fine so far i tried to avoid PCTG in this build as alot of people dont readily have it on hand and it takes way longer to print. Also i took some 800grit around the outside of the cylinder to make putting in, and taking out of the frame a little easier. The cylinder is removeable, printed seperatly this time and make to be a perfect fit into the frame. The sliding door for the salt occasionally does get jammed but works most of the time, will get more reliable as it wears in the shorter time the door is held open the better

The hole in the frame for the salt to feed into the breach may need to be drilled out,. I drilled my hole to 4mm, just big enough for salt to flow freely when the door is pulled open. have a feeling everyones settings may be different. when breach is loaded the same 4-5 shot before reloading rule still applies. Have included larger diameter barrel that works much better with thisversion as well.

This build uses the same Grip/Stock parts and mounting hardware from previous versions as well as the same trigger from v2 I have included 3MF as well as each individual STL. I will post how to photos at the request of anyone who wants it, but im gonna wait and see if this thing actually draws interest first lol it goes together pretty simple. Ive also included 2 different diameter barrels DONT FORGET SILICONE OIL FOR THE AIR PISTON. i use Losi shock oil from my RC pile and works perfectly

Everything works, blaster shoots, hopper feeds, and flies cease to exist. What more do you want?

Rubber bands used - Amazon.com : Rubber Bands Assorted Sizes Mixed Elastic Bands Size82,size94,size84#105 | 50pcs Wide Black Tactical Rubber Bands for Survival Office Supply : Office Products

O-Ring set i bought, i would suggest getting multiple sizes as the grooves are gonna vary a bit from printer to printer. i got a cheap pack, dont forget you need them both for barrels and piston.- ZDBB 1010 Pcs Rubber O Rings Kit 22 Size Universal O-Ring Assortment Set | for Automotive Faucet Pressure Washers Plumbing Sealing Repair,Air or Gas Connections,Resist Oil and Heat: Amazon.com: Tools & Home Improvement

And for the stock any M3 hardware pack will work, as long as it includes m3x45+ nuts.

EDIT- Although i said to print the cylinder in PETG, i feel the need to add if you have PCTG or ABS on hand, please use that instead as its a far superior material for this purpose. 

10/20 EDIT- I was experimenting with stronger bands and noticed the section by the trigger has alot of flex with the original rear frame section. i went ahead and beefed up the back part of the frame in 2 different files. 1 slightly stronger and 1 alot stronger

10/22 EDIT- STEP FILES NOW ADDED

Tagi