1 / 6
SWEET SPOT - Tennis Racket Halo Wall Lamp — zdjęcie 1
1 / 6

SWEET SPOT - Tennis Racket Halo Wall Lamp

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Half-scale classic racket wall lamp: printed strings, a ball at the sweet spot and a hidden LED halo behind it.

Ocena
0 / 5
Polubienia
3
Pobrania
2
Wydruki
0
Wyświetlenia
14
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Home Decor
Licencja
Standard Digital File License

A classic racket that glows from behind

SWEET SPOT is a wall lamp shaped like a classic 80s-style tennis racket, at exactly half scale (343 mm). A ball sits right in the sweet spot and the strings bend around it like a frozen moment of impact. Behind the head a hidden LED ring washes the wall with warm light, so at night the racket floats in a glowing halo with every string in sharp silhouette.

What makes it different

- Real strings: a 16 x 18 string bed printed as the first layers of the front half, so it is crisp, flat and strong. No bridging, no supports.

- Impact detail: the strings bend in a soft ring around the ball, and the ball is squashed against the bed on four tiny feet.

- Classic look: black frame with a thin green pin-stripe on both faces, a brown leather-look grip with overlapping wrap, and a smooth ferrule where the shaft meets the handle.

- Hidden halo: a ring exactly as wide as the frame sits behind the head and carries a 4 mm COB LED strip that points at the wall. From the front you only see the glow.

- Wall posts are printed upright on the back half, so the lamp hangs 30 mm off the wall on three slim posts.

What's included

- 3MF for Bambu Lab X2D, 0.4 mm nozzle, 4 plates, sliced and tested (about 6.5 h in total).

- 3MF for Bambu Lab X2D, 0.2 mm nozzle, 4 plates, for even finer strings (about 30 h in total).

- STL files for every part and colour (P1 to P4 in the file names = plate number).

Plates

- Plate 1: front half with strings (black, white, green).

- Plate 2: back half with the three wall posts (black, green).

- Plate 3: halo ring and handle (black, brown).

- Plate 4: ball (yellow, white).

Hardware you need

- 0.4 m of 5 V USB COB LED strip, 4 mm wide (FCOB), warm white 2700 to 3000 K. You need about 355 mm along the ring.

- A USB power adapter (5 V, 1 A is plenty) and a USB cable with an inline switch or dimmer.

- 3 small brads or pins for the keyholes (shank up to 2 mm, head up to 4.4 mm). The whole lamp weighs only about 100 g.

- CA glue or 5-minute epoxy.

Assembly

1. Glue the front half onto the back half, string side inside. Line up the outline all the way round and hold it with a few rubber bands until the glue sets.

2. Glue the halo ring onto the three small spacer pads on the back of the head, channel facing the wall.

3. Stick the LED strip into the ring channel, LEDs facing the wall. Start and finish at the bottom of the head and run the lead down behind the throat.

4. Push the handle peg into the shaft (glue optional).

5. Glue the ball onto the strings at the sweet spot (its four feet sit on the strings).

6. Hold the lamp against the wall, mark the three post positions, put a brad at each mark, hang the lamp on the keyholes, plug in and switch on.

Print settings (made on a Bambu Lab X2D)

- 0.4 mm nozzle: 0.20 mm layers, 2 walls, 15% infill. 0.2 mm nozzle: 0.12 mm layers.

- No supports: the ball prints standing on its four small feet.

- The front half prints face down: the white strings are the first layers, so make sure the bed is clean and level. A smooth PEI plate gives the nicest strings.

- Colours that share layers are on different nozzles, so there are only a few colour changes.

- Filament (approx.): black 40 g, brown 24 g, white 15 g, yellow 13 g, green 4 g.

- Bed: the head half is 242 x 134 mm and fits any 256 mm-class printer.

Tips

- A matte black PLA hides the layer lines on the frame. Use a dark green for the pin-stripe.

- A dimmer on the USB cable lets you go from a bright halo to a soft night glow.

If you print one, a Make with a photo of your halo would make my day, and a Like helps me keep designing free models. Thank you!

Tagi