1 / 13
IKEA VARIERA Pot Lid Organizer – Under-Cabinet Holder (Command Strip or Screw Mount) — zdjęcie 1
1 / 13

IKEA VARIERA Pot Lid Organizer – Under-Cabinet Holder (Command Strip or Screw Mount)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Hang the IKEA VARIERA lid organizer folded, upside down, under a cabinet. Slides in from the front.

Ocena
0 / 5
Polubienia
2
Pobrania
0
Wydruki
0
Wyświetlenia
54
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Kitchen
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Overview

We use a pot lid organizer set up over a drying mat to prop up drying dishes when they're too large for our sink drying rack or we just have too many, but I don't have a good drawer for it to hide away between uses, so I wanted to print a little under cabinet mount, and not finding one already I decided I should make one.

This is a holder that mounts under a kitchen cabinet and stores an IKEA VARIERA pot lid organizer (stainless steel, art. no. 701.548.00) out of the way. The organizer is folded and hung upside down: its metal strips rest on two rails that run just inside each row of pegs, and the pegs hang down outside the rails. You slide it in from the front, and a small bump at the front edge keeps it from being knocked out. To remove it, lift the front slightly and pull. When in the holder, the organizer is barely visible.

The holder mounts with four large 3M Command Strips, which sit in channels on the mounting face. You can also use four #6 flat-head wood screws instead of the strips or together with them.

Size installed: 150 × 93.7 × 35 mm (W × D × H)

Tested: v3 was printed on a Prusa Core One in white PETG and installed under a kitchen cabinet with four Command Large strips. The folded lid organizer slides in with the feet clearing the top plate, and the base printed flat.

Fit — measurements it was designed around

Measurement

Value

Source

Clear gap between the two peg rows

120 mm

measured

Metal strip stack thickness

8 mm

measured

Rubber feet, past the metal

7.5 mm

measured

Folded length

83 mm

IKEA spec (min length 3¼")

Clearances built in: 3 mm on each side between the tray and the pegs, 2 mm of headroom above the feet, and 2 mm of extra length.

If your pot lid holder measures differently, open the parametric source (variera_holder.py, build123d). Each measurement is a named variable at the top of the file (ROW_GAP, STACK_T, FOOT_H, FOLD_L).

Variable

Value

What to measure

What it controls

ROW_GAP

120 mm

The clear gap between the two rows of pegs, from the inner face of a peg on one side to the inner face of the peg opposite. Measure between the pegs, not centre to centre.

The rails’ positions. Each rail’s outer edge sits SIDE_CLR (3 mm) inside the pegs, so the rails’ outer edges are 114 mm apart.

STACK_T

8 mm

The thickness of the metal strip stack: the stainless crossbars and scissor arms, without the rubber feet.

Part of the headroom between the rails and the top plate.

FOOT_H

7.5 mm

How far the rubber feet stick out past the metal. They point up toward the top plate when the organizer hangs upside down.

The rest of the headroom: STACK_T + FOOT_H + GAP_CLR (2 mm) = 17.5 mm between the rails and the top plate. v1 left this out, which is why the feet hit the plate.

FOLD_L

83 mm

The organizer’s length when fully folded, front to back. This is the one value taken from IKEA’s spec (minimum length 3¼") rather than measured.

How deep the rails are. The retention bump sits at FOLD_L + LEN_CLR (2 mm) = 85 mm from the back wall, and each rail extends about 4.7 mm past the bump.

Printing

Tested setup: Prusa Core One, 0.4 mm nozzle, PrusaSlicer 2.9.6, PETG on the textured PEI sheet. The included 3MF project has all of these settings.

  • Orientation: print it as supplied, with the back wall flat on the bed. Every other wall grows straight up, so it needs no supports.

  • Profile: 0.20 mm STRUCTURAL

  • Perimeters: 4. The plate, back wall, rails and ribs are 3.5–4 mm thick, so 4 perimeters print them almost solid.

  • Infill: 15% (gyroid or grid). Very little of the part is infill, so this hardly matters.

  • Brim: off. The model has mouse ears built in (see below), and a brim would fill the gaps that let them snap off.

  • Temperatures: nozzle 250 °C; bed 90 °C first layer, 85 °C for the other layers; chamber 35 °C (Core One door closed).

  • Material & Time Estimate: about 57 g and about 2 h 55 m (PrusaSlicer, the settings above).

Snap-off mouse ears: the four corners have thin (0.4 mm) anti-warp discs. Each disc is separated from the part by a 0.5 mm gap and joined to it by three small tabs. After printing, bend each ear upward and it snaps off at the tabs. Scrape or trim the small nubs left behind.

Mounting

Command strips (no holes):

  1. Use 4 Large 3M Command Strips (¾" × 3⅝" / 19 × 92 mm).

  2. Clean the cabinet underside with isopropyl alcohol and let it dry.

  3. Lay one strip in each channel, pushed back against the stop at the back end, with the pull tab sticking out the front so you can remove the strip later.

  4. Press the holder in place and hold firm pressure on each strip for 30 seconds.

  5. Wait 1 hour before hanging the organizer.

⚠ 3M rates Command strips for walls, not for ceilings or the underside of a shelf or cabinet, where the weight pulls straight down. The organizer weighs about 600 g. If the strips start to peel, add the screws. My holder went up on 2026-10-19 with Command strips only, and so far they are holding up just fine. I'll update this in a few weeks to let everyone know if I had to add screws to keep it up there.

Screws (optional, or as backup):

  • Imperial: #6 flat-head wood screws.

  • Metric: 3.5 mm countersunk wood or chipboard screws. 4.0 mm also fits.

  • The holes are 4.4 mm across, with a 90° countersink 8.8 mm wide, so both sizes sit flush. The four holes are outside the rails, so you can reach them with a screwdriver from below before the organizer goes in.

  • Choose the length for your cabinet bottom so the tip doesn't come through inside the cabinet. The plate is 3.5 mm thick, so the screw should be no longer than the cabinet bottom's thickness plus about 0.5 mm:

Cabinet bottom

Imperial

Metric

3/8" (9.5 mm)

#6 × 3/8"

3.5 × 10 mm

1/2" (12–13 mm)

#6 × 1/2"

3.5 × 12 mm

5/8" (16 mm), including most European/IKEA cabinets

#6 × 5/8"

3.5 × 16 mm

3/4" (18–19 mm)

#6 × 5/8"

3.5 × 16 mm

  • Drill a 2 mm (5/64") pilot hole, with tape on the bit as a depth stop. In particleboard, stop as soon as the screw head is flush; overtightening strips it.

  • If the cabinet bottom is thin hardboard, use the strips only.

Design notes

  • Why rails between the pegs, not channels around them: hanging upside down, the pegs are the outermost part of the organizer. Nothing sticks out beyond them for a channel to grip, and the crossbars run inward from every peg. A C-channel's inner wall would block the crossbars as the organizer slides in. So the support has to sit under the strips, between the peg rows, and be held from the back.

  • Why two rails, not a full-width tray: each crossbar is a stiff stainless strip, so supporting it near both ends is enough. The middle of the organizer, where the scissor pivots are, no longer rests on anything. This saved significant material & print time from the v2 model (see below)

Version history

v1: full-width tray, first print (superseded; see the Version 1 photos at the end of the gallery)

  • A single tray under the whole strip stack, 10 mm of headroom, sharp footprint corners, and a plain mounting face.

  • The rubber feet didn't fit. They stick up 7.5 mm past the metal once the organizer is upside down, so the organizer couldn't sit level.

  • The back plate's ends lifted off the bed during printing, even with a brim, and the part came out permanently bowed. A long, thin PETG footprint with tall walls on it pulls at its sharp corners as it cools.

v2: full-width tray, fixed (designed, never printed)

  • The gap raised from 10 mm to 17.5 mm for the feet.

  • Rounded footprint corners (6 mm radius), built-in snap-off mouse ears, and a 90 °C first layer against the corner lift.

  • Command strip channels added to the mounting face.

  • Slicer estimate: 118 g, 5 h 43 m. Before printing it, I tried removing the middle of the tray and keeping only the edges, which became v3.

v3: two rails, the current design
  • Keeps every v2 fix: feet clearance, rounded corners, snap-off ears, strip channels.

  • Replaces the tray with two rails, each with a tapered rib and a gusset at the back wall.

  • Slicer estimate: 57 g, 2 h 55 m, about half of v2's filament and time.

  • The v2 tray variant is available on request.

AI disclosure

This model was designed & tested by me with the help of AI tools. This was a valuable exploration for me in the way LLMs can help (and hurt) 3D modeling for additive manufacturing.

What was used:

  • Claude Code (Anthropic, Claude Opus 5.5 model) as a design assistant. It proposed the full-width-tray layout of v1 and v2, wrote the parametric geometry as build123d code, and suggested print and mounting settings. The two-rail layout of v3 was my idea after reviewing the slicer preview; Claude modelled it and compared it with the tray.

  • build123d, an open-source Python CAD library. The model's geometry is build123d code, and the source file is included with this model.

  • 3dp-mcp-server, an MCP server that lets Claude run build123d code, export STL and STEP files, and run printability checks.

  • MCP for Blender, a community add-on that lets Claude drive Blender. It was used to check the fit against a simplified stand-in model of the organizer and to make the preview renders. Those are 3D renders of the actual model, not AI-generated images.

What it helped with

  • Working out the concept. Before modelling anything, it worked out that rails gripping the strips from the sides would hit the pegs as the organizer slides in. That left a tray between the peg rows, held from the back, as the layout that works best, with economy of material and ease of mounting versus using something like two independent C shaped . That shaped the whole design.

  • A parametric design, not a one-off mesh. Every dimension is a named variable in variera_holder.py. Fixing the feet clearance meant changing one number and rebuilding, and anyone remixing it on Printables can do the same.

  • Fast changes between versions. Each round of feedback became a rebuilt, checked model within the same conversation: the feet clearance and corner lift, the snap-off ears, the strip channels.

  • Checks before you spent filament. It confirmed the model was a single watertight solid and checked the mesh for defects. It also checked the fit in Blender against a stand-in organizer, and measured clearances such as the 2 mm between the feet and the plate.

  • The work around the model. Screw sizing in imperial and metric, slicer settings, banners on the v1 photos, and checking the GitHub links.

How the risks were handled:

  • Wrong or made-up dimensions: every dimension the fit depends on was measured by hand on a real VARIERA. Only the folded length comes from IKEA's published spec. The AI's (and my) first version missed the rubber feet; the v1 test print caught that, and it was fixed from v2 onward.

  • Broken geometry: each version was checked automatically to be a single watertight solid. That check earned its place: the first build of v3 had one gusset modelled detached from the rail, and the solid count caught it before anything was printed. The mesh was also checked for non-manifold edges in Blender, and the fit was reviewed visually against the stand-in organizer before printing. I reviewed the sliced G-code preview myself.

  • Bad print or install advice: I checked the suggested settings against my own printer and sheet, and corrected one bad suggestion (glue stick on a textured PEI sheet). Mounting advice includes the Command strip load limitation and screw-length guidance so screws don't come through inside the cabinet.

  • Human in the loop: all measurements, printing, test fitting, and the decision to publish were done by me. No file was published automatically.

  • Originality: this is an original design. No existing models were copied or used as a starting point. IKEA and VARIERA are named only to identify the compatible product; this design isn't affiliated with or endorsed by IKEA.

Tagi