1 / 1
Danfoss RTD-N valve pin extension (+2.5 mm & +3mm) for Sonoff TRVZB and other M30x1.5 smart TRV heads — zdjęcie 1

Danfoss RTD-N valve pin extension (+2.5 mm & +3mm) for Sonoff TRVZB and other M30x1.5 smart TRV heads

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

+2.5 mm press-fit cap for the 2 mm pin of Danfoss RTD-N valves. Fixes Sonoff TRVZB error F5.

Ocena
0 / 5
Polubienia
0
Pobrania
10
Wydruki
0
Wyświetlenia
45
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Share Alike

WHAT IT IS
A tiny press-fit cap that slides onto the control pin of an old Danfoss RTD-N radiator valve and makes it 2.5 mm longer. Nothing more, but it is the missing piece if you want to put a modern M30x1.5 smart head (Sonoff TRVZB in my case) on these valves.

THE PROBLEM
Danfoss RTD-N valves (1980s/90s, common in Czech and German houses) use a proprietary thread and a closing dimension of about 20 mm, while every M30x1.5 head expects 11.5 mm. Printed RTD-N to M30x1.5 adapters exist (I use MakerWorld model 1302682) and the thread fits, but the valve pin then ends up about 9 mm below the adapter rim instead of the 11.5 mm the head expects. The Sonoff TRVZB cannot reach it, reports error F5 (valve not detected) and refuses to calibrate.

THE FIX
This cap adds the missing 2.5 mm or 3.0 mm. With it the head calibrates normally, regulates proportionally and closes the valve fully. Verified on a Sonoff TRVZB with the adapter above; I am fitting 12 radiators with it.

WHY NOT JUST USE AN EXISTING PIN EXTENSION
The generic extensions I found have a 3 mm bore and a deep socket. The RTD-N pin is only 2 mm thick and the thin part is only 5 mm long before the valve gland. A 3 mm bore wobbles and falls off, and a deep socket slides past the thin part and bottoms out on the gland before the valve is closed, so the valve can never close fully and the room overheats.

This design has a 2.2 mm bore (tight press fit on the 2.06 mm pin, no glue needed) and a socket only 2.5 mm deep, so the cap always sits on the pin tip and its lower edge never touches anything, even with the valve fully closed. All force goes through the pin, exactly like with the original Danfoss head.

DIMENSIONS
Outer diameter 6 mm, total height 5 mm (2.5 mm socket + 2.5 mm solid cap). Bore 2.2 mm with a small entry chamfer. Measured pin: 2.06 mm diameter, 5 mm long.

FILES
1) single: one cap.
2) x12: twelve caps on one plate (one house).
3) test_3_bore_sizes: three caps with 2.0 / 2.1 / 2.2 mm bores, marked by 1 / 2 / 3 vertical grooves on the outside. Print this first, pick the one that holds tight on your pin, then print that size. On my Original Prusa i3 MK2S with a 0.4 mm nozzle the 2.2 mm bore (3 grooves) was the right one; your printer may shrink holes differently.

PRINTING
PETG recommended (the head keeps pushing on it for years and it sits on a warm valve). PLA works for testing. Print solid cap down, bore up, no supports, 0.1 to 0.15 mm layers, 100 % infill or at least 4 perimeters. Takes a few minutes.

HOW TO USE
Screw the RTD-N to M30x1.5 adapter on the valve. Push the cap onto the pin tip by hand until it seats on the pin. Then check: push the cap all the way down with your finger (valve closed). There must still be a visible gap between the lower edge of the cap and the valve gland; if it touches, shorten the socket. Mount the head and run its calibration.

Measurements and the "it must never bottom out" requirement are mine; the geometry was generated with AI assistance from those numbers.

Tagi