Liczymy pasujące modele…
Hang your IKEA Mittzon under-desk felt "basket" 10 cm lower. I needed more space for all the cables, KVM switch, power adapters, etc. The "hook" part takes a bit of fiddling to push through and it holds very strong. I recommend using M4…
No need for supports. Prints fine with PLA. Designed to fit around stands like this: These stands are made for at most 15.6inch. This extension allows for deeper laptops to be supported without them leaning back. The laptop shown in the…
Die Armverlängerung besitzt eine kleine Hand, mit der man sich selbst sehr gut am Rücken kratzen kann. Wenn man es größer drucken möchte kann man es im Slicer in Teile schneiden lassen. Das funktioniert hier auch sehr gut! The arm…
This fits: https://a.co/d/5D6Wu38 Depets Large Cat Door (Outer Size 9.9" x 9.2"), 4 Way Locking Cat Flap Door for Interior Exterior Doors, Weatherproof Pet Door The Depets door fits 1-1/4" thick doors. This extension makes it fit 2" thick…
An extension to mount a 13" IPAD on the Joby Grip Tight Pro tripod mount. To install remove the two visible screws on the mount plate and replace base with printed part. Layer height 0.15mm Infill 15% Perimeters: 3 No Supports
Jeremy and Garth of Jaded Parts came up with a great idea for a snap-on two finger (or three!) trigger attachment for the Professor Motor controller. I like their design much better than my own two finger trigger for that controller,…
Hin und wieder sind Gewindebohrer zu kurz um eine schwer zugängliche Stelle zu erreichen. Hier hilft dann eine kleine Verlängerung, die ich für M3 und M4 Gewinde erstellt habe. Sometimes taps are too short to reach a hard-to-reach place.…
remix to accomodate a direct drive upgrade with hydra system. Category: 3D Printer Parts
LID RISER V3 [FRAME EXTENSION KIT] | Vents | LED Strip | Hinges *If you have any issues with printing or assembly, feel free to message me, and I'll do my best to assist you 😉. /////ATTENTION *Because of the seam inside the walls, the…
It is 180mm deep and 120mm high but you're welcome to make it your own size I printed it with 15% infill and PLA. It took 2h45min on the Ender 3v3 Plus
This is a remix of https://www.printables.com/model/821953-btt-pi-and-tft35-spi-extension-for-ender-3 , a design that I made earlier for my own Ender3 V1. I did this remix since an Ender3 V2 owner liked my design and wanted to use is on…
I printed this part out of PETG with 4-5 walls and 10% infill basically prints the walls solid. I had to print these in two parts as they are too big for my printer. The mating parts have an interference fit that okay, not perfect, but…
The corners of the aluminium extrusion profile of my Hammer table extension are rounded but still sharp enough to hurt if you bump against it. To cover them up, you can use this cap.
Extensin for https://www.amazon.de/gp/product/B0BMX9V334/ref=ppx_yo_dt_b_asin_title_o05_s00?ie=UTF8&psc=1&language=en_GB to ensure that the keys do not get stuck on the keyrings. Printed with 100% infill 0,4 nozzle, 0,2 layer. There is a…
I am working on adding a larger heel part soon. The arms must be inserted into the inner sides of the toe arms on the WinWing Orion 2. They jus snap in. The heel part slides in after that and can be fastened inthe preferred position.…
-+- Keeps stuff from falling -+- Great for items stored close to the edge of a table or desk, like plants. -+- Required Parts -+- Prints: 1 x Extension 2 x Clamps Hardware: 2 x M4 Bolts 2 x M4 Washers 6 x M4 Nuts -+- How to use -+- After…
Heavy-Duty mount for the Yellow Jacket 3 outlet 12 gauge “contractor” extension cord. May fit other similar designs. It accommodates #8 wood screws, including cabinet/washer head screws. Printed in PETG. Model is designed to print with…
I needed something to mount the Link2Home extension cord reel I bought from Costco to my Storewall so I've created yet another custom holder. Uses 3x M5 20mm length bolts and nuts from this kit here: https://www.amazon.com/dp/B07HVRJW5J…
Edit the sketch called "spline" to adjust it to your liking. It's best to just delete the constraints and moving the points with the move tool or dragging them manually. In the past, I've used a combination of plumbing tape and a felt…
G E R M A N Türgriffverlängerung für die Elia-Scheiben. Meine Frau ärgerte sich immer wieder, wenn sie mit der dicken Winterjacke die Türen öffnen wollte. Die Scheibe drückte ihr in die Achsel. Das sei unangenehm. Also entwarf ich auf die…
ENGLISH: Holder for the Engelmann mirrors. These were also sold by Opel for the Manta or the Kadett. The holders break over the years. Likewise, extensions for these mirrors can still be found here if the installation position on the…
********** ENGLISH *********** Mounts and extensions for the cameras of the usual motorcycle dashccams. The new version has the following improvements: Base arms detached from support plates, so now the "eyes" are printed from "loops" and…
Extension arms for your digital calipers, adds another 100mm extra space to measure stuff that does not fit the calipers. These are not ultra precise, but will get the job done for most projects.
An extension accessory for the iRobot H1 handheld vacuum. Print as many as you need to clean up out-of-reach places.
Bracket for wall mounting with M4 countersunk screws
These are extensions of the Nilfisk Vacuum Cleaner Buddy II, but it can be used with any vacuum cleaner that has the hose with an internal diameter of 35 mm. Total length 240 mm There 2 models: One has a small angled tip and the second…
A wall mountable slide in holder that allows for easy fixture and removal of your RCD extension power box. Attach to your wall or any surface with 10 gauge countersunk screws; I've added recessed flanges for the screw heads to sit in…
Leg extenstions to raise the height of a Corsair 3500X case (or similar) 50mm or 80mm off the ground. Suitable for improved fan clearance on carpet. Both 50mm and 80mm files provided. (80mm shown in photo) Printed in PLA with 15% infill.…
Our RV couch has cup holders that don't work with small cups and glasses, as they have an odd recess. I designed these to allow smaller cups and to eliminate the narrow recess at the bottom of the standard cup holders. Can be installed as…
inspired by SCUF Thumbstick grips and designed to fit controllers for Xbox One, Xbox Series, Playstation 5, and Nintendo Switch Pro Controller (not joycons) No glue is required, but it is recommended Print cap in TPU Support only for…
Inspired by https://makerworld.com/en/models/589181 I like to believe my version has a little more style and function to it. The holding ring has a hole for an M3 threaded insert but this hole is blind, ending in a flexure which should…
Simple Extension to have the Sprayer a bit higher. Fits the 4.6mm line. I used ASA as its fairly thin and will be used outside.
My boss has a saber on her shelf, but since it has the blade attached she cant use 90% of the saber stand on this site. so, I took another design and shortened it in tinker cad (I just cut and stitched the models back together).
For those of you who are annoyed by having to mount your bike light of to the side or simply can’t because your handlebars taper of leaving no space. This solution has been around on the consumer market for a while, but I noticed it could…
IKEA UTAKA Bed Frame Adapter (for Thicker Mattresses) Please Post Makes The IKEA UTAKA stacking bed is originally designed for very thin mattresses. If you use thicker mattresses, the two bed frames will no longer fit together properly.…
Discord: https://discord.gg/nJvfCKD2jx a community Server to chat share projects etc. Feel free to message me if you need something :D This feet lift the Printer like 4,5cm off the floor You can check if they fit on other printers or…
This extends the shower head away from the wall. Our shower is on the wall over the bathtub, the curvature of the bathtub was preventing me from standing fully under the shower. There is minimal support under the body to prevent if from…
This 25mm table extension can be stuck under the original table of your Fendt caravan. Have a look into my CAMPING & Co. Collection to find more useful camping gadgets. Have fun. Material: PETG: Infill: 25% Layerheight: 0,2mm
Single part ring to extend a Silvercrest Food Dryer to fit Filament Rolls inside. Could work with other Food Dryers as well. It is printable on large printers only, like the Prusa XL. I created several sizes so you can print the size best…
Subterra II insert for figurines and all extensions. Use 10x1 magnets for horizontal figurines and 4x1 magnets for vertical figurines. You can print support and glue it after if you dont use magnet
Barrage board game insert with all extensions.
What if it turns out that your bin is too small for your stuff or your tools turn out to be a bit higher than expected and now you can't stack anymore? Print a new bin, sure you can, but you can also print an extention, way less waste…
It’s not a milestone in 3D printing part design — but once again, a useful little helper! This is an extension for the Creality Multi K1 filament holder . It offers a practical slot for essential tools and safely guides the PTFE tube to…
If you want to combine a basket with the usage of panniers (for example by Ortlieb), this might be the solution. This is an extension to have a second railing on a given luggage rack which doesn't have one. Tested in combination with…
These are replacement/extension links for the Elegoo Centauri Carbon cable chain. I modeled them based on the original chain to help fix the tight bend radius at the toolhead. A lot of people on Reddit and Discord have noticed that the…
This extension foot is designed for the Ultimulti legs for Coreboxx , allowing it to be mounted securely to the floor at a 40° angle . It provides additional stability and flexibility for installations where the Ultimulti needs to be…
Model printed in ABS at 0.2 mm layer height with 6 perimeters, 4 top layers, 4 bottom layers, and 25% infill. The print was paused at layer 80 to insert an M8 nut.
This is a vent extension for the 2nd gen Toyota Tundra that allows for proper airflow with aftermarket floor mats that have a tendency to block the vents. Printed in ABS and PETG. Print with mesh screen down. Given the length of the model…
Dehydrator height extensions to make a filament dryer. I've tried to make these really robust. They print with no supports on the solid part, and supports only on the upper side of the window for the part with the humidity gauge. They'll…
The metal rods I had were not long enough so I made an extension. This model is made for the IKEA Kallax Filament Storage Rack from @Celta.
Original model of a stereotaxic rig protractor extension for juvenile songbird surgery. This extension, perfect for veterinarian working on passerines, fits perfectly the standard ear bar of a stereotaxic rig and increase the precision of…
This design comes in two versions. The story behind it: Originally I designed the fender extension to have that rounded trailing edge. However my first print ran into a little problem and the parts were cut off a couple of millimeters…
I generally don't like it when the sensor is so close to the housing. This simple mod makes loading and unloading the filament much more convenient and reduces bending in the filament path. BOM: 1x M3x50 Take a look at the photo gallery.…
Thanks for supporting me over the years! Files are now free for personal use. Consider buying me an ice cream or something :) @ https://ko-fi.com/palmtopper STL Files for the Nerf Rival Saturn Stock Extension. Adds the extra length to the…
Extender and fixation of Steam Valve HTC Base Station. Clips to hold the cable. STEP FILE Included. https://amzn.eu/d/0dEfJ3i You will need a 30mm M6 screw and locking nut if you want to fixate the the top part and the usual short camera…
k1se cabin extension 150 mm. The original was 40 mm. I extended it.
Print on left or right side without supports. Connects multiple IKEA Spruttig hangers. Better use of your space. I saw this model , which is nice and uses less filament and print time. I decided to do my own design, as I wanted a bit more…
I took a trip to IKEA recently and decided to buy some kitchenware supplies to help with my resin printing workflow. Among my finds were the 1.8l Korken glass jars with lids and the small Medarbetare sieve / tea strainer that I decided…
This front panel is designed for clean and secure mounting of a Type-C extension cable in an enclosure or device housing. The Type-C extension is fixed to the panel using its original (stock) screws, ensuring precise alignment of the…
This model is an extension of the original cup base of the Delta Q Mini coffee machine. The original cup base positions the cup relatively far from the coffee spout, which can cause splashing during extration, leading to mess. The…
A friction fit base that fits onto the bottom of your case and will hold the small accessory case to keep everything together. No glue or hardware needed. Recommended to print 100% solid for durability. Recommended to print 102% scale…
This usefull addition to your Scenic will give you extra comfort during your ride. The standard cup holder is hard to reach and the location where you are supposed to place you key is horrible. This addition features: Two cupholders of…
Checkout my new improved v2 here A taller extension for you STRECHR stack. This allows you to add in a half ring when you are in between full height extensions. The original extension is 15mm and this version is 23mm. I've updated the…
Remixed to use as extensions for installing a small Skadis section in the side of the BRÄNNBOLL Gaming Station Desk. You'll need: Print two “A” and two “B” sections plus the Connectors . M3 x 16mm screws and nuts - 16 of each. One SKÅDIS…
A shortened stock tube extension for use with an existing G&G stock tube extension.
This model is an MX‑G System Sprinkler Extension designed for easy integration into modular setups. It includes an M5 internal thread compatible with Festo QSM‑M5 pneumatic couplings or any similar push‑in connector. The design provides…
Materials Screws 8x Original screws from feet 8-14x M3 x 6mm 2-4x per Support Bar to Side Rail I use 2 per bar, but there are holes for 4 1x per Rear Side Plate to Side Rail 14-22x M3 x 8mm 4-12x Side Rail to Disk Drive 3x per Front Side…
Feet extions for Babelio Gate (Model with cat door, unsure about others). Take measurements. Step included so you can resize if you want, just extrude the back face.
This project allows for a discrete installation of a USB-C port directly under your desk edge, providing instant access for charging or data transfer without desktop clutter or the need to reach for your PC. The mount is specifically…
You will need a longer rod to build the CynthiAWP. I you dont want to buy a longer rod, you can use the original Cynthia rod and extend it with this print. Just screw it on the bottom end.
Original build: https://cults3d.com/en/3d-model/game/mech-battle-arena I printed a bunch of these mech battle arena parts and assumed I could build some combination of the parts for a "two map battlemat" but it required an additional 25mm…
The original model allowed the antenna to flop out and I wanted the antenna to stay internally, so I modified the design to fully encapsulate it. The added fins are to make it able to take more force since it needs to be printed…
I need a mounting to hold my USB C extension cable in a fixed position.
A mounting bracket to attach a pruning saw blade to a standard extension pole with an ACME (broom handle) thread. It uses the carriage bolt and wing nut from the original wood handle. I have included a FreeCAD model of this design so you…
The cord hook design accommodates a heavy duty, 12 AWG / 3 conductor, extension cord with a maximum diameter of 15mm. The corner hook design allows the extension cord to be gently bent around a 90-degree corner. This allows the cord to…
I created this to static balance the front wheel of an RV-12. I printed it with PETG-CF but anything should work. The extensions are a tight fit but can be pulled off. I placed wheel weights inside the wheel. To use on the main wheels, it…
I extended the bottom bar and to support the current bar original pieces so that its still modular. This bar supports a 2018 Mac Mini and similar size micro computers.
UK Double socket desk clamp with 20mm extension in height for clearing wires for mains plugs
This is a 5cm extension for VKB Gladiator joystick that retains the twist axis action. After couple of iterations and few of hours of flying I'm happy to share this. Before diving in... THIS MOD MIGHT BRAKE YOUR JOYSTICK. YOU WERE WARNED!…
this elongates the linear rail in case you have a shorter one to use. it fits the table top cut out as well.
This small clip holder is designed for 1/4 inch ratchet extensions. Unlike open holders, the extension snaps securely into place and stays put. A perfect addition to existing Honeycomb Storage Wall tool storage. If you like this model, I…
Used extended screws to remount fan. And snipped out the bullseye on the hotend shroud
Description This is not a groundbreaking idea — many similar solutions already exist. My goal was to create a modification that does not require alternative screws and keeps structural changes to a minimum . ALEX Drawer unit, white, 36x70…
As said previously, this is a holder for the Bticino S3631USGB/S3631USDB thin extension cords, so it can be mounted vertically on the back of a desk or furniture (as long as you can/want to use nails of any other method to attach it).…
I created these because the normal extension holders take up a ton of room and having things vertical save even more space. The 1/4 in vertical will need to be printed w/ a .4mm nozzle to allow smaller details to print so that it is…
M42 to M42 macro extension tube designed specifically for 3D printing. Firm grip for secure mounting Textured internal surface for reduced internal reflections Working aperture Chamfered edges to counter elephant's foot Chamfered threads…
For that, you first need the house. https://www.printables.com/model/1573935-house-1
PLEASE Like if you like & review and post your makes! Thanks! for the hinge you will need M4 hex socket screws and nuts (10 or 12mm) (for each foot 2 pieces) For the adjustable slider you will need m4 hecx socket screws (20mm) (for each…
What is it? This is a multi-piece extension for the RatRig V Core 4 500 IDEX. What does it do? The main purpose is to have the touchscreen from BTT the Pi TFT70 V2.1 be integrated onto the frame. But this also raises the top panel by…
I added the option of mounting a screw.
![CREALITY K1 MAX - LID RISER V3 [FRAME EXTENSION KIT]](https://media.printables.com/media/prints/1113589/images/8603616_60a7f138-6ba6-4188-bbf6-cdb880ec998a_f4300ca9-7596-4f4e-9ef3-f72931737ef2/k1max_projects_covers.jpg)
