1 / 3
Zalman N5 MF Top I/O Cover – Cat-Proof Hinged Lid — zdjęcie 1
1 / 3

Zalman N5 MF Top I/O Cover – Cat-Proof Hinged Lid

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Taped-on hinged cover for the top I/O panel of the Zalman N5 MF, so cats can't press power/reset.

Ocena
0 / 5
Polubienia
1
Pobrania
0
Wydruki
0
Wyświetlenia
6
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Computers
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

🇬🇧 English

My cat loves sleeping on top of my PC and kept hitting the power / reset buttons on the top I/O panel of my Zalman N5 MF case. This hinged cover protects the whole top I/O strip – no drilling, it's taped on.

How it works

  • A rear rail is taped onto the top dust filter, right behind the I/O panel. The hinge is on this rail.

  • The lid is hinged at the back. When closed it rests on the rail at the back and with its front foot on the flat strip in front of the ports – the cat's weight never touches the buttons.

  • Lift it from the front and all ports and buttons are accessible. At ~145° it leans on the rail and stays open.

  • ~20 mm of clearance under the lid – enough for fingers or a small USB dongle.

Parts

  • Lid (kapak) – printed upside down, top face on the bed

  • Rear rail (arka ray) – printed with the taped face on the bed

  • Pin – a 160 mm piece of 1.75 mm filament (or a 2 mm nail / wire). Melt/flatten both ends slightly so it can't slide out.

  • Fit test (olcu_sablonu) – a thin 1.8 mm template of the I/O plate. Print it first (a few minutes) and lay it on your case to check the fit.

The 3MF contains the lid and rail on one plate (fits a 250×250 bed).

Print settings

PLA or PETG, 0.2 mm layers, 0.4 nozzle, 3–4 walls, 20–30 % infill.

Assembly

  1. Align the lid and rail hinge knuckles and push the filament pin through (2.2 mm hole). Flatten the ends with a hot nozzle or soldering iron.

  2. Clean the filter frame and stick the rail on with double-sided tape, behind the I/O panel.

Note: Dimensions were derived from Zalman's product photos and manual drawing (±2 mm), and the printed part fits my case. The model is parametric (Blender Python script) – lid height, thickness etc. can be adjusted.


🇹🇷 Türkçe

Kedim bilgisayar kasasının üstünde uyumayı seviyor ve Zalman N5 MF kasanın üst I/O panelindeki power / reset düğmelerine basıp duruyordu. Bu menteşeli kapak üstteki tüm I/O şeridini koruyor; delik yok, bantla yapışıyor.

Nasıl çalışır

  • Arka ray, I/O panelinin hemen arkasında üst toz filtresinin üzerine bantlanır; menteşe bu raydadır.

  • Kapak arkadan menteşeli. Kapalıyken arkada raya, önde ayağıyla portların önündeki düz banda oturur; kedinin ağırlığı düğmelere hiç binmez.

  • Önden kaldırınca tüm port ve düğmeler açılır; ~145°'de raya dayanıp açık kalır.

  • Kapağın altında ~20 mm boşluk var (parmak veya küçük USB alıcı için).

Parçalar

  • Kapak – ters basılır (üst yüzü tablada)

  • Arka ray – bant yüzü tablada

  • Pim – 160 mm'lik 1.75 mm filament parçası (veya 2 mm çivi/tel); kaymaması için iki ucunu hafifçe eritip ezin.

  • Ölçü şablonu – 1.8 mm kalınlığında I/O plakası şablonu. Önce bunu basıp kasanın üstüne koyarak uyumu kontrol edin.

Baskı ayarları

PLA veya PETG, 0.2 mm katman, 0.4 nozul, 3–4 duvar, %20–30 doluluk.

Montaj

  1. Kapak ve rayın menteşe topuzlarını hizalayıp filament pimi geçirin (2.2 mm delik). Uçlarını sıcak nozul veya havya ile ezin.

  2. Filtre çerçevesini temizleyip rayı çift taraflı bantla I/O panelinin arkasına yapıştırın.

Not: Ölçüler Zalman'ın ürün fotoğrafı ve kılavuz çiziminden çıkarıldı (±2 mm); basılan parça benim kasama oturdu. Model parametrik (Blender Python betiği); kapak yüksekliği, kalınlık vb. değiştirilebilir.

Tagi