Immersion Blender Stand – Motor Stands Dry, Shaft and Whisk Hang Over Drip Windows, Cord Hook
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
One-piece dock for a stick blender: motor on an open cone, shaft and whisk hang blade-down over drip windows, cord hook.
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 5
- Wydruki
- 0
- Wyświetlenia
- 29
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Kitchen
- Licencja
- Creative Commons — Attribution — Noncommercial
One printed dock keeps a stick blender together on the worktop: the motor stands coupling-down on an open cone, the washed shaft and whisk hang blade-down from two V-slots over windows in the base, and the coiled cord hangs on a hook at the back.
Measure first: shaft tube 22-40 mm with a collar at least 5 mm wider (10 mm for tubes over 32 mm), whisk stem 8-10 mm, at most about 190 mm from the collar's underside to the tip, motor body up to 72 mm. Prints as one part turned 45°: it needs a bed of at least 210 x 210 mm (the part turned 45° covers 201.3 x 201.3 mm; about 205 mm is enough with the skirt off) and 200 mm of height - not 180 mm beds.
Validation status (please read): digitally validated only - fit ranges, drip paths and stability are calculated from the CAD. It has not been physically printed or tested, and not tried with a real blender. All pictures are renders of the print file with a generic proxy blender (no brand), and one is a drawing - none is a photograph.
Features
Dry where it must be dry: the motor stands coupling-down on an open 45° cone - the centre is open, so crumbs and moisture fall through and the coupling never stands in a cup.
Drips fall clear: the wet tools touch the dock only at the collar or gearbox and the upper tube or stem; the bell or balloon touches nothing and hangs over a window cut through the base. Drips from the rim of a bell (up to 72 mm) or balloon (up to 66 mm) fall through to the worktop - checked with 72 downward rays per tool on the CAD at three reference sizes (no hits), not with water. Water running down a wet tube still wets the V-slot and the ear; wipe the dock now and then.
Self-centring V-slots: slide a tool in from the front; it settles where the tube touches both 45° sides and the collar rests on the ear (large 33-40 mm tubes may hang a few degrees tilted).
The cord has a place: coil it in small loops (about 55 mm across) and hang the coil on the J-hook at the back - room for a 1.2 m cord (calculated); a twist tie keeps the coil neat.
One part, one plate, no supports, no hardware; the ready-to-print project carries the settings.
Will my blender fit?
It fits by measured ranges, not by brand. Measure your blender with calipers, or wrap a paper strip round the part and divide its length by 3.14.
Part | Fits | Notes |
|---|---|---|
Motor body | up to 72 mm across (checked; 75 mm is the calculated bore limit) | stands coupling-down in the 80 mm bore |
Motor coupling end (where the shaft clicks on) | 40-75 mm | rests on the 45° cone (36 mm open centre) |
Blending shaft tube | 22-40 mm, with a collar at least 5 mm wider (10 mm wider for tubes over 32 mm) | bell up to 72 mm over the drip window |
Whisk stem | 8-10 mm, with a gearbox at least 5 mm wider | balloon up to 66 mm over the drip window |
Hanging length (underside of collar / gearbox to the tip) | up to about 190 mm | the tip stays at least 8 mm above the worktop; a longer tool stands its bell on the worktop inside the window |
Cord | about 1.2 m | coiled in small loops on the J-hook |
Shafts that taper continuously with no collar step at least 5 mm wider than the tube will not hang.
Dimensions
Oval base 212 x 190 mm, 222 mm across the ears, 200 mm high; with a typical motor docked the motor top is about 220 mm above the worktop.
Files
stick_blender_dock_complete.3mf - ready-to-print PrusaSlicer project: the dock placed diagonally on one plate, PETG profile and the per-object settings embedded, no supports.
dock.stl / dock.step - the part.
model.py - the parametric CadQuery source: cone, V-slot range, window sizes, ear spacing, cord hook. It refuses geometry that would not fit the bed or would collide; other combinations are not checked.
Print settings
PETG (or ASA). PLA is not recommended in a warm kitchen.
0.4 mm nozzle, 0.20 mm layers, 3 perimeters, 35 % rectilinear infill laid every 2nd layer, no supports - keep these settings: the dock's weight (about 0.3 kg) is part of its stability, and lighter infill makes it easier to tip.
Upright on its base, turned 45° on the bed. The 3MF is laid out for a 220 x 220 bed; on a 250 x 210 bed press Arrange (about 4 mm to spare - turn the skirt off).
The base is a large PETG first layer: use a textured sheet, or a release layer such as glue stick on smooth PEI. Above about 100 mm two 18 mm handles carry the ears - slow the upper half on bed-slinger printers to avoid ringing.
About 6 h on a Prusa MK4S (0.20 mm SPEED preset, 291 g) or 16 h on a slow generic profile (299 g) - PrusaSlicer estimates.
How to use it
Dock the motor first: drop it in coupling-down.
Shaft: wash, shake off and slide it into an ear's V-slot from the front so it hangs blade-down.
Whisk: wash the wire part as your blender's maker says, dry it, click it back into its gearbox and hang it by the gearbox.
Cord: coil it in small loops and hang the coil on the hook at the back.
Take the tools off before you lift the motor out. Store the blender unplugged.
Put a cloth or a small dish under the windows if you want to catch drips - water that lands next to the base can creep under its flat edge.
Limitations
Digitally validated only: not printed, not tried with a real blender.
Not universal - measure your blender against the ranges above.
Stability is calculated, not measured: with all three parts a sideways push of about 4.3-4.8 N at the top of the tallest part tips it (3.1-3.7 N with the motor alone). Empty, or with the motor out and one tool hung, the dock is light: about 1.2-1.3 N at an ear top tips it - steady it with your other hand.
Large shaft tubes (33-40 mm) may hang a few degrees tilted if the collar is smooth and wet.
Not a drying device and not a holder for a running or plugged-in blender. Hand-wash; PETG is not made for hot dishwasher cycles.
Pictures
Renders of the print file and one drawing, not photographs: the dock on a kitchen worktop holding a generic stick blender (cover), the same on a studio background, the dry and wet sides with drip paths, the fit drawing, the dimensions, the print plate and the dock in sage from behind with the coiled cord. The blender is a generic proxy without brand shapes or logos; not affiliated with or endorsed by any blender maker.