DC Barrel Plug Size Key – Tell 5.5x2.1 From 5.5x2.5 Without Calipers, Plus a Socket Probe
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Flat printed key that reads a DC power plug's size - outer diameter, bore and barrel length - plus a socket probe.
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 6
- Wydruki
- 0
- Wyświetlenia
- 23
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Tools
- Licencja
- Creative Commons — Attribution — Noncommercial
A flat printed key, plus a small socket probe, that reads the size of a coaxial DC power plug ("barrel plug") - the round plugs on adapters for routers, guitar pedals, LED strips, keyboards, soldering irons and laptops - without calipers. The two most common plugs, 5.5 x 2.1 and 5.5 x 2.5 mm, look the same, and calipers cannot measure a 2 mm bore. Here the plug's face stops at the step labelled with its bore.
Validation status (please read): checked in CAD (an identification matrix of 25 sizes with plug tolerance and 0.1 mm print error) and in the slicer. It has not been physically printed or tested on real plugs; readings depend on your printer's dimensional accuracy. All images are renders of the CAD model or diagrams; the plugs and sockets are modelled stand-ins built from datasheet dimensions (the sockets are drawn cut away) - none is a photograph.
What it reads
Outer diameter, read continuously in a taper slot (2.2-8.6 mm), with marks at 2.5 / 3 / 3.5 / 4 / 4.5 / 4.75 / 5 / 5.5 / 6 / 6.3 / 6.5 / 7.4 / 8.
Bore of pin-less plugs on a stepped tongue at the key's edge: 1.1 / 1.35 / 1.7 / 2.1 / 2.5 / 3+. The deepest deciding step is 8.3 mm in - shorter than a 5.5 mm plug's barrel - so bulky moulded or right-angle plug bodies stay outside the key and read the same as slim ones.
Laptop and other pinned plugs: outer diameter + the centre pin (seen by eye) name them in the size chart.
Barrel length: 9-14 mm ticks against a stop tab.
Device sockets (5.5 mm only) with the socket probe: slides about 8 mm in = centre pin 2.0 mm or less (5.5 x 2.1 - a 5.5 x 1.7 socket also lets it in, check the label); stops at once = 2.5 mm pin (5.5 x 2.5). Its closed hexagonal bore cannot be spread by a pin.
25 common sizes were checked in CAD: each reads differently within plug tolerance + 0.1 mm print error, except these near-twins the key cannot separate: 2.35x0.7 / 2.5x0.7 / 2.5x0.8; 3.4x1.3 / 3.5x1.1 / 3.5x1.35; 6.3x3.0 / 6.5x3.0; 6.5x3.4 / 6.5x4.3; 5.5x3.0 / 5.5x3.3. The size chart is in the images.
How to use it
Unplugged connectors only.
Outer diameter: from the unmarked back, push the barrel up through the round hole and slide it toward the narrow end until it stops (do not force); read the nearest mark.
Look into the plug. Centre pin: note it - outer diameter + pin name it in the size chart. No pin: push the plug straight onto the tongue (barrel in the notch, body outside the key) until its face stops and read the label at that step. Won't go on = 1.1 mm or smaller; face passes the 2.5 step = 3+. Barrels wider than 6.5 mm skip the tongue.
Socket: push the probe straight into the device socket. Slides about 8 mm in = pin 2.0 mm or smaller; stops at once = 2.5 mm pin - if it stops, rock it gently and press again (a pin that misses the hole also stops it). Does not go in = not a 5.5 mm socket. Do not force it.
Length: lay the plug against the stop tab and read the shoulder (9.5-10 for most plugs, 12-12.5 for many laptop plugs). Look the readings up in the size chart.
Print settings
PETG recommended (the thin tongue flexes instead of snapping); PLA is fine for careful use.
0.4 mm nozzle, 0.2 mm layers with a 0.2 mm first layer - the tongue's reading flat sits at 0.4-0.6 mm; draft layer plans such as 0.28 or 0.3 mm can miss it and make the bore steps read narrow.
No supports. Key flat, engraved face up; probe standing on its flange - as in the project. Keep elephant-foot compensation at its default.
About 1 h 7 min and 13 g for both parts (PrusaSlicer estimate, generic profile).
Accuracy matters (design budget ±0.1 mm per width). Optional checks: 3 mm and 5 mm drill-bit shanks should stop on the 3 and 5 marks of the slot; a 2.0 mm shank slides through the probe and a 2.5 mm one does not (if the 2.0 does not pass, open the hole by hand with a 2.2 mm drill).
Files
dc_barrel_plug_key_complete.3mf - ready-to-print PrusaSlicer project, key + probe on one plate.
dc_barrel_plug_key.stl and dc_barrel_plug_socket_probe.stl.
model.py + stroke_font.py - the CadQuery source with the step widths, slot taper, print-error budget and size table as parameters (run
python stroke_font.pyonce to create font_polys.json before model.py).
Dimensions
Key 104 x 49 x 3.2 mm (with the 3 mm stop tab), key-ring hole 4.4 mm. Socket probe 22.7 x 11 x 10.9 mm (barrel 5.3 x 8.5 mm, hexagonal bore 2.25 mm across flats) with a key-ring tab.
Limitations
Not physically printed or tested; a printer far outside the ±0.1 mm budget reads one mark off.
It cannot tell polarity, voltage or current - always check the device's label; never use it on a powered connector.
Plugs with a centre pin are identified by outer diameter + pin; their bore is not read. The socket test covers 5.5 mm sockets only.
A reading that is not in the size chart is a size the key does not list - check the device label.
Slide and push gently; do not lever a plug sideways on the 1 mm tongue. Forcing the probe onto a 2.5 pin can ream its hole.
Pictures
Renders of the CAD model and diagrams, not photographs: plugs in the key (cover), the bore reading at the 2.5 step, how to read it, the outer-diameter reading, the size chart, the socket probe over a 2.0 and a 2.5 mm pin (sockets cut away), and the two printed parts.