1 / 7
Cat-Resistant Plant Pot Cover – Petal Lid Fits Inside the Rim, Closes Around the Trunk, 16 Sizes — zdjęcie 1
1 / 7

Cat-Resistant Plant Pot Cover – Petal Lid Fits Inside the Rim, Closes Around the Trunk, 16 Sizes

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Flower lid that sits inside the pot rim and closes around the trunk: dig-resistant, water passes, no repotting.

Ocena
0 / 5
Polubienia
4
Pobrania
2
Wydruki
0
Wyświetlenia
40
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Pets
Licencja
Creative Commons — Attribution — Noncommercial

Petal Guard is a two-piece, flower-shaped lid that sits inside your plant pot's rim and closes around the trunk - no repotting. Rows of overlapping petals rise from a seat that rests on the rim's inner edge; between the petals, oblique slots let water and air through, but there is no straight way down to the soil for a paw. A raised double-petal heart closes around the trunk, a port lets you check the soil with a moisture meter or probe, and two small soil pegs hold the lid down. The two halves are the same print. It looks like part of the planter, not like black plastic mesh.

Validation status (please read): designed and checked in CAD and in the slicer (no supports); the load figure is a static hand calculation. It has not been physically printed or tested, and not tried with a real cat - it is dig-resistant, not cat-proof. Print the fit ring first. All images are renders of the exported CAD; the plant, pot and soil are generic props - none is a photograph.

Features

  • Inset: rests on the rim's inner edge (thin plastic, rounded, lipless or tapered rims and ceramic cachepots). No lip wraps over the outside of the pot; the edge rises 2.5-5.5 mm above the rim.

  • Overlapping petal rows: no straight path to the soil within 20° of vertical (computed in CAD); 3.5-3.8 mm oblique slots pass water and air, and every slot drains downward.

  • Raised double-petal heart: closes to about 12 mm and opens for a trunk up to 18-28 mm (rated per size). A 13-18 mm port (by size) for a moisture meter or probe - a fingertip fits from size 122 up.

  • Hidden spokes tie every petal row to the seat. A static hand calculation for a 5.4 kg cat standing on a 60 mm centre pad gives a spoke stress of 12 MPa (PETG about 47 MPa) - a calculation, not a load test.

  • Two identical halves with a pin and hole that mate; two barbed soil pegs.

  • Print it in your planter's colour - sage, terracotta, cream or charcoal.

Find your size

Measure the rim's inside diameter and pick the band (±3 mm): PG 110 (107-113 mm), 116, 122, 128, 134, 140, 146, 152, 158, 164, 170, 176, 182, 188, 194 and PG 200 (197-203 mm). Then print that band's fit ring (23-42 min) and set it in the rim beside the trunk: it should rest on the rim edge, 2.5-5.5 mm proud. The lid is 13 mm tall (heart 13-20 mm by size) and reaches about 7.5-10.5 mm below the rim, so leave at least 15 mm between the soil and the rim top. Size 164: lid 172 mm across.

Which files?

  • fitring_DXXX.3mf - the fit ring for each band; print it first.

  • petal-guard_DXXX_complete.3mf - the whole lid for each band (two halves + two pegs; bands 110-182 on one plate, 188-200 on two plates).

  • petal-guard_DXXX_half.stl (print twice) and petal-guard_peg.stl (print twice, same for every size).

  • model.py - the CadQuery source: rim diameter, petal spacing, heart size and port.

Print settings

  • PETG (heat up to about 68 °C, tougher petals). PLA only in shaded rooms - it softens in the sun.

  • 0.4 mm nozzle, 0.20 mm layers, no supports. As installed: underside on the bed, petals up - as placed in the projects.

  • Examples (PrusaSlicer estimates, generic PETG profile): size 110 half 2 h 38 min / 23 g; size 164 half 5 h 23 min / 50 g (whole lid on one plate about 11 h 24 min); size 200 half 8 h 50 min / 75 g; fit ring 164 about 34 min / 9 g; peg 22 min / 1.5 g.

Assembly

  1. Measure the rim inside diameter of the pot (or cachepot), pick the band and check it with the fit ring.

  2. Make sure there is about 15 mm or more between the soil and the rim top.

  3. Put the two halves around the trunk (pin into hole) and press the lid into the rim until it rests on the edge.

  4. Push the two pegs through their collars into the soil until the heads sit on the collars.

Water as usual through the petals or the port; check moisture through the port. Rinse the lid by hand (no dishwasher). To take it out, pull the pegs and lift the halves apart.

Limitations

  • Not physically printed or tested, and not tried with a real cat. Dig-resistant, not cat-proof; urine still drains through.

  • Round pots only; a single trunk (or a compact stem group inside the heart opening) standing near the pot centre - off-centre by at most half the difference between the rated trunk and yours (e.g. about 2.5 mm for a 20 mm trunk in size 164). Leaning or off-centre trunks will not let the lid seat. Wide clump plants are out of scope.

  • In a cachepot, the nursery pot's rim must sit at least 12 mm below the cachepot rim.

  • Rim inside diameter 107-203 mm; larger floor pots are not covered.

  • The load figure is a static hand calculation; jumps, heavier cats and paw loads between spokes are outside it. Small petals: not a toy.

Pictures

Renders of the exported CAD, not photographs: the lid around a trunk in a stoneware pot (cover), the lid alone in the rim, a labelled section, the two halves going on, the size chart, the heart close-up and four colourways. Plants, pots and soil are generic props.

Tagi