1 / 6
Self-Righting Bud Vase – Round Flask for a Glass Test Tube, Rocks Back Upright When Knocked — zdjęcie 1
1 / 6

Self-Righting Bud Vase – Round Flask for a Glass Test Tube, Rocks Back Upright When Knocked

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Round-flask bud vase weighted low with steel washers: knock it and it rocks back upright; a glass tube holds the water.

Ocena
0 / 5
Polubienia
1
Pobrania
0
Wydruki
0
Wyświetlenia
8
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Home Decor
Licencja
Creative Commons — Attribution — Noncommercial

All images are renders. This design is digitally validated; it has not been physically printed or tested.

A round-bottomed bud vase in the shape of a classic round flask, with a belt at its widest point. Ten steel washers sealed in the bottom put the centre of mass well below the centre of the round bottom, so when the vase is tipped it rocks back upright. The belt meets the table at about 63° and acts as a stop. The water is held by a standard glass test tube (16 x 130 mm, or 16 x 160 mm for the tall version) that stands on the bottom through the washers, so the print never has to be watertight - lift the tube out to clean or refill.

Validation status (please read): checked in CAD (statics with conservative masses over the whole washer tolerance range, water level at the stop) and in the slicer (no supports). It has not been physically printed or tested. All images are renders of the CAD model; the glass tube, water, washers and stem are generic proxies - none is a photograph.

Features

  • Rocks back upright from any tilt up to the belt stop (about 63°), checked in CAD: the centre of mass sits at least 10.4 mm (tall version 8.3 mm) below the centre of the round bottom for any ISO 7093 washer thickness (2.7-3.3 mm), with 12 ml of water and a 10 g stem.

  • The belt is a stop: to roll over it, the centre of mass has to rise at least 12.6 mm more (tall version 11.1 mm).

  • With 12 ml of water the water stays inside the tube even at the stop: in CAD the rim's lowest point stays at least 6.6 mm above the water with a 6 mm stem in the tube (14.5 mm without a stem; tall version 20 mm).

  • Standard parts: a 16 mm round-bottom glass test tube (DURAN size) and ten ISO 7093 M16 large washers (17 / 50 / 3 mm).

  • A printed keeper ring holds the washers and centres the upper body; printed shim rings, chosen at the dry fit, take up the washers' thickness tolerance (at most 0.5 mm of play in CAD).

  • Support-free prints; no watertight printing needed.

Dimensions

Height 140.5 mm (16 x 130 tube) or 170.5 mm (16 x 160 tube); 96 mm round body, 108 mm belt. About 0.6 kg with washers, tube and water (estimate).

Files

  • Ready-to-print PrusaSlicer projects: rock-back_core-keeper_PLA (core + keeper, both heights; about 94 g, 8 h 50 min), rock-back_shims_PLA (5 shim rings 1.0-2.4 mm; about 17 g, 1 h 13 min) and ONE upper/cap project for your tube - rock-back_16x130_upper-cap_PLA (about 92 g, 6 h 29 min) or rock-back_16x160_upper-cap_PLA (about 97 g, 6 h 52 min). Generic 220 mm profile - switch to your printer, press Arrange, slice.

  • STL files: cap, core, keeper and shims (same for both heights) and the two upper bodies.

  • model.py - the CadQuery source: tube size, sphere radius, belt, washer count.

Print settings

  • PLA (matte); PETG also suitable.

  • 0.4 mm nozzle, 0.20 mm layers, no supports. The cap prints solid (100 % infill, 0.12 mm layers) because it is the lowest mass; the core at 40 % gyroid - all set in the projects.

  • As exported: cap flat face down, core equator face down, upper body belt face down, keeper ring wide face down, shims flat.

  • All parts incl. shims: about 203 g / 16 h 33 min (130 mm tube) or 209 g / 16 h 56 min (160 mm) - PrusaSlicer estimates.

You also need

10 x ISO 7093 M16 washers (17 / 50 / 3 mm), one round-bottom glass test tube 16 x 130 mm (or 16 x 160 mm for the tall body), glue for plastic (CA or epoxy).

Assembly

  1. Glue the cap into the core's narrow end: its bevelled rim seats in the core's bevel and centres it.

  2. Stand the glass tube in the pocket and drop the 10 washers over it (keep the tube in place until the glue has set - it keeps the washers centred). Put the keeper ring on the washers (plug down, collar up) and measure how far its shoulder sits below the core's top face. Take the keeper out and lay shims on the washers that add up to a little less than that depth - up to 0.4 mm less, never more (1 notch = 1.0 mm, 2 = 1.2, 3 = 1.6, 4 = 2.0, 5 = 2.4 mm). Example: 3.0 mm washers leave about 4.2 mm -> 2.0 + 1.2 + 1.0. Without calipers: lay a ruler across the core face beside the collar and try shims until the shoulder is just below the face. Put the keeper back on the shims.

  3. Dry-fit the upper body (no glue, belt face down): it must sit on the core's face with no gap all round - if it rocks or shows a gap, swap one shim for the next thinner one. Then glue it on; the keeper's collar centres the upper body.

Use: stand the tube in the vase, pour in 12 ml of water (about 2 1/2 teaspoons) and put in one stem.

Limitations

  • It rocks back up to the belt stop (about 63°). Pushed hard over the belt it can tip onto its side, and the water then spills; lying on its side, the tube can slide about 6 mm out.

  • It can roll off the edge of a table or shelf; it is not pet-proof or child-proof.

  • 12 ml of water at most; one stem up to about 10 g and 6 mm thick, not much taller than shown - heavier or taller flowers lift the centre of mass.

  • The two glue joints are permanent; the washers stay inside.

  • Not physically printed or tested.

Pictures

Renders of the CAD model, not photographs: both heights on a shelf (cover), the vase at its stop angle, a cutaway of the inside, both heights on a studio background, the parts exploded and the dimensions.

Tagi