1 / 8
Hush Chime – 5-Tube Pentatonic Wind Chime Kit With a One-Push Off Position (DIY Aluminium Tube) — zdjęcie 1
1 / 8

Hush Chime – 5-Tube Pentatonic Wind Chime Kit With a One-Push Off Position (DIY Aluminium Tube)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Pentatonic wind chime kit from DIY-store aluminium tube: push the sail up to silence it, pull it down to play.

Ocena
0 / 5
Polubienia
0
Pobrania
0
Wydruki
0
Wyświetlenia
10
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial

Hush Chime is a kit that turns DIY-store aluminium tube (25 x 1.5 mm) into a five-tone pentatonic wind chime (C5 "Dawn": C5 D5 E5 G5 A5) - with a built-in off position. Six printed parts hang the tubes and carry the striker: a crown (spreader), a keeper that holds every tube at its lower node, and a keyed wand (stem, clip, terracotta striker lens, cross sail). Push the sail up until it clicks and the striker parks inside the keeper: the chime goes quiet. Pull it down to play again. A printed drilling jig puts both node holes of every tube square, at the calculated node.

Validation status (please read): designed and checked in CAD and in the slicer; pitch, detent and fuse forces are calculations. It has not been physically printed, assembled or tested - no real wind, tone or docking trial yet. All images are renders of the exported CAD with tubes modelled at the calculated lengths; the balcony, plants and drill are generic props - none is a photograph.

Features

  • Hush in one push: the striker parks inside a cup under the keeper (30° lead-in, printed detent - entry about 1.8-3.4 N, hold about 3.2 N, beam calculation). The node cords hold the keeper down, so one hand is enough. Nothing to fit, remove or lose - unlike a separate silencer.

  • Strikes near the bottom edge: the tilted, keyed lens meets every tube 8-25 mm above its bottom edge although the bottoms are staggered (computed with the wand swung up to 6°).

  • No tube-on-tube clash: the keeper links all five tubes at their lower node, so they swing together.

  • The load is not in plastic alone: every tube hangs on its own cord to a stainless ring; the crown is only a spreader.

  • Pitch by calculation: lengths from the free-free beam formula for 25 x 1.5 mm tube with both alloy bounds carried - cut 5 mm long and trim to pitch with a spectrum app.

  • Drilling jig: a bridge with a drill guide and one stop pin in five dotted holes - both node holes of every tube at the calculated distance, without a drill press. Tube places are marked 1-5 dots on the keeper and the jig.

  • Cross sail: four drop-shaped fins catch the wind from any direction. Its snap doubles as a fuse, calculated to pop off at about 20-38 N, so a yank on the sail cannot load the hook much beyond that (calculated, untested).

Cut list (Dawn, 25 x 1.5 mm tube, calculated)

Note

Hz

Tube length

Alloy bounds

Node holes from each end

Cut first

C5

523.25

534.7 mm

533.2-536.1

119.9 mm

540 mm

D5

587.33

504.7 mm

503.3-506.0

113.1 mm

510 mm

E5

659.26

476.3 mm

475.0-477.6

106.8 mm

481 mm

G5

783.99

436.8 mm

435.6-438.0

97.9 mm

442 mm

A5

880.00

412.3 mm

411.2-413.4

92.4 mm

417 mm

From three 1 m bars: C5 + A5 from one, D5 + G5 from another, E5 from the third (at least 37 mm spare on each bar after two saw kerfs).

Dimensions

About 793 mm from the ring to the sail tip; keeper about 123 mm across; about 0.8 kg hanging (calculated). Tubes 412-535 mm long.

Which files?

  • hush-chime_complete.3mf - all three plates in one PrusaSlicer project; or the single plates chime_A_keeper_wand (keeper, stem, clip, lens - about 3 h 58 min), chime_B_crown_sail (crown, cross sail - about 4 h 32 min) and the optional chime_C_drilling_jig (jig + stop pin - about 4 h 19 min).

  • STL files of every part and model.py - the CadQuery source (notes, tube OD and wall, alloy constants; it re-plans the tube order and the lens tilt).

Print settings

  • PETG for covered balconies; ASA where the chime sees full sun. Lens in an accent colour if you have one.

  • 0.4 mm nozzle, 0.20 mm layers, no supports, parts as placed in the projects (sail standing on its socket end with a 6 mm brim).

  • All 8 printed parts about 158 g of filament (PrusaSlicer estimates on a generic profile).

You also need

Aluminium round tube 25 x 1.5 mm (3 bars of 1 m), about 4 m of 2 mm UV-resistant braided cord (or 80 lb braided line), a stainless ring 25-40 mm, a hook rated for the chime. Tools: tube cutter (or hacksaw + mitre box), hand drill with a 3.5 mm bit, deburring tool or file, a spectrum app on your phone.

Assembly

  1. Print plates A and B; plate C (drilling jig + pin) is optional tooling.

  2. Cut each tube 5 mm long, deburr, tap it and trim toward its note in a spectrum app (read the lowest strong peak; 1 mm off C5 moves it about 6 cents).

  3. Drill the node holes: stop pin in the hole with that tube's dots, slide the tube through the bridge to the pin, drill through both walls; turn the tube end for end and drill again. Deburr.

  4. Each tube goes through the keeper collar with its dots (1 dot = shortest ... 5 dots = longest). Line up its lower node holes with the slanted hole through the collar, feed a short cord on a stiff wire or needle from the outer side through collar and tube, pick it out of the open window and knot both ends outside the collar.

  5. Tie a cord through each tube's top node holes, up through the crown hole above it (stopper knot under the crown), to the stainless ring. Adjust until the keeper hangs level.

  6. Wand: push the stem up through the keeper hub (the bulb clicks past the fingers), snap the clip into the groove on top, pull the stem down until the clip rests on the hub; slide the lens on from below (keyed) and push the sail onto the stem end until it clicks. The D-bores are close fits - test-fit and file lightly if a print runs tight.

  7. Hang the ring on a hook under cover, out of reach of children.

Play: pull the sail down until it unclicks. Hush: push the sail up until it clicks. Bring the chime in for storms.

Limitations

  • Not physically printed, assembled or tested. Tone, loudness, sustain and the keeper's effect on the tone are not measured; the tube alloy is usually not stated, so cut long and trim by app.

  • Needs metalwork: cutting, drilling and deburring aluminium tube.

  • Hushed, the wand keeps a little play and may tick softly inside the cup in strong wind; a tube rocking in its cord play can occasionally touch the cup lip.

  • Hang it inboard under a cover from a rated hook. Not a structural or child-safe product; UV and frost ageing of the printed parts and cord is not verified (use ASA in full sun).

Pictures

Renders of the exported CAD, not photographs: the lower chime against a garden (cover), PLAY vs HUSH, the whole chime under a balcony soffit, a cutaway of the hush dock, the kit, the cut list, the drilling jig and three colourways.

Tagi