CYM Case 2432S028R – ESP32-2432S028R (CYD-2432S028) Case (battery + GPS)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
This 3D-printable, two-part enclosure houses an **ESP32-2432S028R** board
- Ocena
- 0 / 5
- Polubienia
- 3
- Pobrania
- 12
- Wydruki
- 0
- Wyświetlenia
- 76
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Electronics
- Licencja
- Creative Commons — Attribution — Noncommercial — NoDerivatives
If you like my design and plan to download it, please show your appreciation by giving it a like!!
SUMMARY / DESCRIPTION
This 3D-printable, two-part enclosure houses an ESP32-2432S028R board (the "CYD" with a 2.8" resistive touch screen, USB-C and micro-USB) for the Cheap Yellow Monster (CYM) firmware — https://github.com/JimGat/CYM (select the board as CYD-2432S028 in the Web Flasher). It turns the bare board into a pocket device with its own battery, charging and GPS.
What fits inside
- The ESP32-2432S028R main board, held by 4 × M3 × 7 screws from the front into the brass hex standoffs that come with the board's kit
- A 1100 mAh LiPo battery (3.7 V, 1.25 mm plug, up to 53 × 30.5 × 7.5 mm)
- A Youmile LX-LCBST charge + 5 V boost module (USB-C charging)
- An ATGM336H GPS module with its antenna
- An SS12D00G slide switch (3 mm lever) and the screen stylus
Features
- Two parts: a lower case and a front frame that wraps the screen and sits flush with it
- Flexible BOOT and RESET buttons on the back face
- Roofed pocket for the GPS antenna and a routed channel for its cable
- Pockets for the battery, charge module and GPS module; a pocket for the slide switch (O / I)
- A full-length channel for the stylus
- 1.5 mm holes for the RGB LED, the two charge LEDs and the GPS LED
- A hole in the front frame for the on-board light sensor
- Engraved port labels: MICRO, USB-C, P5, SD, CN1, P3, SPK, CHG, and O / I
- The CHG (charge) port is charging-only and carries no data — see the manual
Printing
- Two parts, printed flat, no supports
- Case 88.9 × 52.9 × 15.8 mm; front frame 88.9 × 52.9 × 3.5 mm; combined thickness 19.3 mm
- About 20 g of PLA
- Full slicer settings are in the Print Settings below
Assembly
Full illustrated instructions are in the attached manual (EN / TR / DE, PDF): general information (board specifications, pinout, parts list), 3D printing, assembly and flashing the firmware with the CYM Web Flasher. It covers the wiring (GPS → CN1: GND · IO22 · IO27 · 3.3V, battery → charge module, module 5 V output → switch → board S3/S1), setting the module output to 5.0 V before assembly, and changing the on-board charge-current resistor to 2 kΩ (≈580 mA). Note: on this board the GPS module is powered from 3.3 V on CN1, not from the 4-pin P5 socket used on the NM-CYD-C5 — follow the manual.
License: CC BY-NC-ND 4.0 — you may print and use the case yourself and share the unmodified files with credit. Selling printed cases or the files, commercial use and publishing modified files are not allowed without permission. The CYM firmware is a separate project with its own license.
CYM Case 2432S028R · Revision 1 · Designed and made by @birolt29 @alen29
PRINT SETTINGS
- Printer brand: Creality
- Printer: Ender-3 S1 Pro
- Rafts: No
- Supports: No
- Resolution: 0.16 mm
- Infill: 15%
- Filament brand / color / material: SUNLU / Black / PLA (PLA+)
- Notes:
0.4 mm nozzle. 3 walls (Arachne / variable line width), outer wall first, outer-wall speed 30 mm/s. Nozzle 210 °C (first layer) / 205 °C, bed 60 / 55 °C. Flow ≈0.95. Elephant-foot compensation 0.1 mm. No supports anywhere. Case: flat closed back face on the plate, open side up. Front frame: back face (toward the board) on the plate, lettering up. Dry the filament before printing so small lettering does not fill in. PLA+ is enough; use PETG only if the device will sit in a hot environment.