Slim MagSafe enclosure for RAK4631 + RAK19007 for Meshtastic / Meshcore
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A two-part case for RAKwireless RAK4631 core on a RAK19007 board, sticks to the back of an iPhone with magsafe magnets
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 1
- Wydruki
- 0
- Wyświetlenia
- 29
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Gadgets
- Licencja
- Creative Commons — Public Domain
Outer size | 65.2 x 60.2 mm, 12.2 mm thick |
|---|---|
Parts |
|
Screws | 4 x M2 x 6 mm countersunk (flat head). M2 x 8 also works. |
Magnets | 54 mm MagSafe magnet array, up to 1.9 mm thick |
Antennas | Plain lid: both kit flex antennas inside. SMA lid: LoRa whip on an SMA bulkhead, BLE flex inside |
What's inside
The base plate faces the phone. A 0.8 mm skin, then a 2.0 mm deep, 54.6 mm
pocket for the magnet array. Four pedestals with 2.4 mm pegs locate the board
through its mounting holes.The lid is the whole outer shell. The base plate nests inside it, flush with the
phone-side edge, so the only visible seam is against the phone. Four posts come
down from the ceiling and hold the board on its pegs. Four corner bosses take the
screws, which go in from the phone side and are hidden once the puck is on the
phone.USB-C opening with a 1 mm counterbore so the plug body can reach the port.
A 1.8 mm hole next to it lines up with the reset switch (press it with a SIM tool).
Three 1 mm pinholes let the two user LEDs and the charge LED show through.The ceiling has a shallow relief over the battery connector, which is the tallest
part on the board. You do not need to remove that connector.Two 46 x 11 mm, 0.35 mm deep recesses in the ceiling, one along each long wall,
are landing spots for the flex antennas (the kit's LoRa strip is 35 x 7 mm).
SMA lid (lid_sma.stl)
Same shell, but the long wall that faces up when the puck is on the phone carries
a standard SMA bulkhead jack for the kit's IPEX-to-SMA pigtail. A 6.6 mm hole goes
through the wall and a hex pocket inside grips the jack's 8 mm hex flange, so you
tighten the nut from outside without the jack spinning. Put the kit's washer under
the nut. The board sits so close to the short end walls that the jack body only fits
on a long wall, which is why the SMA is there and not next to the USB-C.
With the SMA lid, mount the puck with the SMA edge up: the whip points past the top
of the phone and the USB cable leaves sideways. Only the -Y antenna recess remains,
for the BLE flex antenna.
Material: PLA or PETG. PETG is a little tougher for the thin screw bosses.
Layer height 0.2 mm (0.16 for a nicer top). 3 walls, 4 top/bottom layers.
lid.stlandlid_sma.stlare already upside down: print as is, outer top face on the bed.base_plate.stlprints as is, phone-side face on the bed.No supports needed. The USB opening bridges 13 mm, which any printer handles.
Rough first layer or elephant's foot will scratch a phone: use a smooth build
plate and, if needed, enable elephant-foot compensation (about 0.1 mm).
Assemble
Trim the magnet array sticker: cut off the tail with the two bar magnets and the
two small ears so only the 54 mm ring is left. Check polarity against your phone
first (the array should snap onto the phone in the orientation it will be glued).Stick the magnet array into the pocket of the base plate, magnet side up (away
from the phone), adhesive against the skin. If the array is thinner than 2 mm
that is fine; it stays put on its own adhesive.Stick the flex antennas into the two recesses in the lid ceiling (BLE in one,
LoRa in the other, or BLE only with the SMA lid) and coil the IPEX cables into
short loops. With the SMA lid, fit the pigtail jack through the wall first: hex
into the pocket from inside, washer and nut outside. Connect every antenna to the
RAK4631 before powering it.Drop the board onto the four pegs, USB-C toward the end wall with the openings.
Lower the lid over the board and plate. The USB-C port should be centred in its
opening.Turn the puck over and drive the four M2 screws in from the phone side. Stop as
soon as the heads sit below the surface. Do not over-tighten in PLA.