LayersFactory
Zgłoś model
1 / 8
TBS Source One V6 DJI O3 Antenna Mount – FlyFishRC Osprey 40 mm Stubby (TPU) — zdjęcie 1
1 / 8

TBS Source One V6 DJI O3 Antenna Mount – FlyFishRC Osprey 40 mm Stubby (TPU)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

FPV GEEK

FPV GEEK

@FPVGEEK_2617187

TPU mount for a FlyFishRC Osprey 40 mm stubby on the TBS Source One V6. Both u.FL cables run through it into the frame.

Ocena
0 / 5
Polubienia
0
Pobrania
1
Wydruki
0
Wyświetlenia
29
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
RC & Robotics
Licencja
Creative Commons — Attribution — Noncommercial
SzczegółyPliki (2)Wydruki i komentarze (Wydruki: 0) (Komentarze: 0)Remiksy (0)Kolekcje (1)Powiązane

▶ More builds on my channel: youtube.com/@fpv-geek

Yesterday I tore off both original DJI O3 antennas flying a bando. So I switched to a FlyFishRC Osprey 40 mm stubby and designed this TPU mount for my TBS Source One V6. The antenna sits almost completely inside the TPU: only the top 2 mm stick out.

What it fits

  • Frame: TBS Source One V6, on the two rear standoffs (22 mm apart, 5 mm aluminium standoffs)

  • Antenna: FlyFishRC Osprey 40 mm dual-band u.FL antenna for DJI O3 (16 mm head)

  • Air unit: DJI O3. Both u.FL cables run through the mount into the frame.

  • Air unit mount: the lowest 6.3 mm of the standoffs stay free, so an air unit mount that clamps the same standoffs fits underneath (see the photo with the top plate off).

Details

  • Cup: 16.2 mm inside, 15 mm deep. The antenna is a push fit in the TPU, no glue.

  • Angle: 40 degrees back.

  • Cable channel: 6.2 mm, from the bottom of the cup into the frame. It comes out between the standoffs, and both u.FL plugs pass through one after the other.

  • No screws: the mount slides over the standoffs and the top plate holds it down. It has a recess for the edge of the top plate.

  • Standoff holes: 5.1 mm, a snug fit in TPU.

Install

  1. Take off the top plate.

  2. Push the antenna into the cup from the top.

  3. Feed the two u.FL plugs through the cable channel, one after the other.

  4. Slide the mount over the two rear standoffs, above the air unit mount.

  5. Plug the u.FL cables into the O3 and put the top plate back on.

Print settings

  • Printer: Bambu Lab P2S, 0.4 mm nozzle, Textured PEI plate

  • Filament: TPU, 240 °C nozzle, 35 °C plate

  • Layer height: 0.2 mm

  • Walls: 4, top / bottom layers 5 / 3

  • Infill: 15 % cubic

  • Supports: tree (auto), 30 degrees

  • Brim: auto

  • Orientation: as in the 3MF, standing on its flat bottom

  • Print time: 51 min, filament: 7.8 g TPU (Bambu Studio estimate)

Files

  • 3MF: my Bambu Studio project with the profile I printed it with

  • STL: for any other slicer

The standoff spacing is checked against TBS's own O4 antenna mount from the open Source One files: github.com/tbs-trappy/source_one

Tagi

tpufpvtbsfreestylesourceoneantennamount5inchospreystubbyuflo3djio3bandoflyfishrcsourceonev6