Pellet Deduster for Rabbit Feed – Shop Vacuum Powered (Narex VYS 33-21 L)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Removes dust and crumbs from hay/feed pellets : a conical bar screen plus shop-vacuum suction, flow verified in CFD.
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 1
- Wydruki
- 0
- Wyświetlenia
- 17
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Pets
- Licencja
- Creative Commons — Attribution — Noncommercial
Edit 2026-10-29 (2): added a flat 1 mm TPU gasket for the lid flange (part 6), it goes between the flange and the barrel lid. Added a tighter variant of the lid flange (part 4b) – the original one slid almost all the way up the outlet taper on my print.
Edit 2026-10-29: fixed narrow slots in the lower body where the duct joins the chamber in front of the vacuum port – air leaked in from the chamber along each side of the duct.
Edit 2026-10-27: fixed the screen – its reinforcing rings started in mid-air, now they are part of the cone and print without supports. Corrected the printing notes: the lower body needs supports under the vacuum port.
Deduster for hay / feed pellets for rabbits (designed for ~8 × 10 mm cloverleaf pellets). You pour the pellets into the hopper on top, they slide over a conical bar screen and fall through the bottom outlet into a barrel. Dust and small crumbs are sucked through the gaps in the screen and leave through the side port into a shop vacuum. The hopper on top is the only air inlet.
The vacuum port is my vysavacBase connector for the Narex VYS 33-21 L hose (see my collection Makita dust extraction adapters – Narex); the hose end clicks straight in.
Parts
Each part is a separate file, already oriented for printing:
- Spodni díl (lower body) – collector funnel under the screen, neck, duct and vacuum port, Ø150 outlet at the bottom. 244 × 236 × 205 mm – fits a 256 mm bed (Bambu X1C). Needs supports under the vacuum port.
- Horní díl (upper body with hopper) – bolts onto the lower body (M4 bolts on the flange).
- Síto (screen) – conical spiral bar screen, 50° cone, max. gap 4.5 mm. Sits on a lip of the collector and is clamped by 3 posts against the upper body.
- Příruba víka (lid flange) – glued onto the slightly tapered Ø150 bottom outlet; 6 plain M4 holes on PCD 180 to bolt the deduster onto a barrel lid. Ø196 × 16 mm. Two variants:
-
4-priruba-vika– original, 0.15 mm radial clearance; on my print it slid almost all the way up the taper. -4b-priruba-vika-tesnejsi– tighter (no clearance, bore 0.3 mm smaller), should seat ~3 mm lower. Pick the one that suits your printer's tolerances. - Těsnění (seal) – 3 × 3 mm ring for the groove between the upper and lower body, print in TPU.
- Těsnění příruby víka (lid flange gasket) – flat 1 mm gasket between the lid flange and the barrel lid, Ø159 / Ø196 with the 6 bolt holes, print in TPU. Its bore is ~2 mm wider than the flange bore, so it clears the outlet tube that sticks out of the flange.
The Fusion 360 source (.f3d) is included.
Printing
-
The lower body needs supports: print it upright (Ø150 outlet down, with a brim) and add supports under the vacuum port and inside its roof. It can't be printed flange-down.
-
The other parts print without supports (45° rule).
- Material: ASA or PETG, both seals (parts 5 and 6) in TPU.
- Assembled height is 365 mm.
Use
- Set the vacuum to about 2/3 power (~45 l/s). In the CFD model, at full power a fully covered screen starts holding the pellets; at ~2/3 they still slide off.
- The barrel lid is not included – it needs an opening of at least Ø156 mm and 6 holes on PCD 180 for M4 bolts.
CFD
The airflow was simulated in OpenFOAM (simpleFoam, k-ω SST) with particle tracking (the last image, labels in Czech). At 45 l/s about 86 % of 50 µm dust and 92 % of 2 mm crumbs end up in the vacuum, while ~94 % of pellets go to the barrel. Pressure loss of the deduster is about 3.4 kPa, mostly in the neck and duct.
Notes
I designed this myself and I'm testing it right now – once I'm done, I'll add photos and my experience with it.
Provided as is, without any warranty.
License
CC BY-NC 4.0 – remix and share freely with credit, but no commercial use.