Open-firenet ESP32-S3 Magnetic Case for Pellet Stoves Rika (YD-ESP32-S3, Hides the USB-A Port)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Snap-fit PETG case for a YD-ESP32-S3 running Open-firenet. Four magnets; a cap hides the Rika stove's USB-A plug.
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 1
- Wydruki
- 1
- Wyświetlenia
- 35
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Electronics
- Licencja
- Creative Commons — Attribution
A small case for the ESP32-S3 board that runs open-firenet, the open firmware that replaces the stove's Firenet Wi-Fi module and brings the stove into Home Assistant. The board plugs into the USB-A port on the back of the stove. This case sticks to the steel panel with four magnets and covers that port with an open-bottom cap, so the plug, the short cable and the board disappear into one tidy box.
I use it on a RIKA PARO. It does not depend on the stove model: any steel panel with a USB-A port sticking straight out of it will do, as long as there is 110 × 33 mm of flat metal around the port.
Open Firenet edition (multicolour)
New: a lid with the Open Firenet logo and name, in the colours of the project's website. The case is now listed on the Open Firenet hardware page, and the logo is used with the maintainer's permission.
coque-capot-multicolore.3mf: black lid, orange logo and "Firenet", white "Open", BOOT and RST, inlaid 0.6 mm deep. The lid prints top face down, so the colour changes only happen in the first 3 layers. PrusaSlicer: black on extruder 1, orange on 2, white on 3.
Other slicers: load coque-capot-logo.stl (black), coque-capot-orange.stl and coque-capot-blanc.stl as parts of one object. They share the same origin.
Single colour: coque-capot-logo.stl alone gives the logo engraved 0.6 mm deep.
The base (coque-fond.stl) does not change. The original plain lid and the plate are still available.
Cable: besides a right-angle USB-A plug, a short cable with side-angled (left/right) 90° plugs on both ends fits on paper: the USB-A head sticks out about 10 mm, and the USB-C side must lead the cable towards the COM port. Not tested yet.
The three new product images are AI-generated (Gemini via OpenRouter) from renders of the actual model.
Features
Made for the YD-ESP32-S3 (VCC-GND, ESP32-S3-WROOM-1), 27.94 × 57.15 mm, with no pin headers soldered.
Four 8 × 3 mm neodymium magnets in pockets behind a 0.4 mm skin, so the plastic touches the panel, not the magnets.
Open-bottom cap at one end: set it over the stove's USB-A port. The right-angle plug and a loop of cable fit underneath.
Snap-fit lid: a 1 mm rabbet and four clips, no screws. A notch at the antenna end lets you open it with a small screwdriver.
The board sits on four 1.5 mm pads, with end stops that take the load when you plug or unplug the cable.
Paper-clip holes for BOOT and RST, a 0.4 mm skin over the status LED, and vent slots along the lid.
No thick plastic over the antenna, which points away from the cap.
32.6 × 108.1 × 15.6 mm closed.
What you need
A YD-ESP32-S3 board (N16R8 here) without pin headers. Pins soldered underneath will not fit.
Four 8 × 3 mm neodymium disc magnets, and a drop of cyanoacrylate glue for each.
A right-angle (90°) USB-A male plug on the stove side, sticking out 12 mm or less from the panel. A straight USB-A plug (about 35 mm) does not fit under the cap.
A straight USB-C plug on the board side, overmould up to about 25 mm long and 12 × 7 mm in section.
The shortest USB-A to USB-C cable you can find: the cap holds the plug and a small loop. I did not test a specific length.
Print settings
PETG, not PLA: the case lives on a stove. I have not measured the panel temperature where it sits.
0.2 mm layers, 4 perimeters, 20 % infill.
No supports. The base prints flat on its back; the lid is already flipped, top face on the bed.
coque-firenet-plateau.3mf holds both parts on one plate (250 × 220 bed). The STL files are the same parts, one per file. coque.py is the parametric build123d source.
Assembly
Glue the four magnets into their pockets, all with the same pole facing out.
Plug the USB-C cable into the board's "USB" port (the right-hand one, seen from the component side with the USB-C ports towards you). The "COM" port stays free for flashing.
Drop the board onto its pads, ports towards the cap, between the end stops.
Snap the lid on.
Plug the right-angle USB-A plug into the stove, fold the cable into the cap and set the case on the panel.
Once closed, only the BOOT and RST holes are reachable. The COM port is inside, so plan on OTA updates and open the case for a USB flash.
The positions of the LED, buttons and USB-C ports come from the official board drawing (± 0.5 mm), with clearance added. The heights of the module and the USB-C sockets are estimates.
Designed with AI assistance (parametric Python script).
En français
Coque aimantée pour la carte YD-ESP32-S3 qui fait tourner open-firenet (firmware libre qui remplace le module Wi-Fi Firenet du poêle et le relie à Home Assistant). Quatre aimants néodyme 8 × 3 mm la tiennent sur la tôle ; un capuchon sans fond recouvre le port USB-A du poêle, la fiche coudée et la boucle du câble. Couvercle clipsé sans vis, trous pour BOOT et RST, fenêtre fine pour la LED. Il faut une carte sans connecteurs soudés, une fiche USB-A coudée à 90° (12 mm maximum) et une fiche USB-C droite. Impression en PETG, sans supports, pièces déjà orientées.
Édition Open Firenet : couvercle multicolore avec le logo et le nom du projet (3MF pour PrusaSlicer, ou STL par couleur), incrusté sur 0,6 mm. Logo utilisé avec l'accord du mainteneur. Les trois nouvelles images sont générées par IA à partir des rendus du modèle.