1 / 3
Snap-In Pipe, Conduit & Handle Wall Clip - Parametric (16-42 mm presets) — zdjęcie 1
1 / 3

Snap-In Pipe, Conduit & Handle Wall Clip - Parametric (16-42 mm presets)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Screw-mount snap clip for PVC pipe, conduit, tubing, dowels and tool handles. Set your exact diameter and print it with

Ocena
0 / 5
Polubienia
1
Pobrania
2
Wydruki
0
Wyświetlenia
8
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution

A C-shaped snap clip designed to hold round items on a wall, under a bench or inside a cabinet: PVC pipe, electrical conduit, tubing, broom and tool handles, dowels and rods.

Set the outside diameter, the snap opening and the wall thickness. Choose a centre screw (driven through the clip mouth into a recessed head pocket), side tabs, both, or none (glue or tape).

The profile is extruded straight up, so it prints flat with no supports, and the screw holes are teardrops.

Presets: 16 mm conduit, 1/2", 3/4", 1" and 1-1/4" PVC (nominal ODs 21.3, 26.7, 33.4 and 42.2 mm).

Notes and limits:

  • Not a code-approved strap or hanger: where electrical or plumbing codes require listed supports for conduit or pipe, use those. Not load-tested.

  • Snap force depends on material and snap_opening; PLA is stiffer, so widen the opening a little

  • Pipe sizes are nominal: measure your actual OD

  • Previews are OpenSCAD renders, not photos of real prints.

Included files: stl/pipe-clip-snap-mount_16mm-conduit.stl, stl/pipe-clip-snap-mount_half-inch-pvc-21.3mm.stl, stl/pipe-clip-snap-mount_3-4in-pvc-26.7mm.stl, stl/pipe-clip-snap-mount_1in-pvc-33.4mm.stl, stl/pipe-clip-snap-mount_1-25in-pvc-42.2mm.stl, pipe-clip-snap-mount.scad (OpenSCAD source with a Customizer panel), preview renders.

How to customize: install the free OpenSCAD (openscad.org), open the .scad, choose Window > Customizer, change the values, then press F6 (Render) and Export STL.

Parametric OpenSCAD design by Maker Hollow Studio. The files were checked automatically (watertight, correct size, prints without supports) but have not yet been test-printed. Preview images are OpenSCAD renders.

Print settings

  • Material: PETG for the best snap; PLA works but can crack if the opening is too small

  • 0.2 mm layers, 3-4 perimeters, 20% infill

  • Supports: none

  • Orientation: as exported (flat on the bed)

Parameter guide

Group | Parameter | Default | Range / options | What it does

Pipe / Tube | pipe_diameter | 21.3 | 5:0.1:120 | Outside diameter of the pipe or handle you want to hold (mm)

Pipe / Tube | clearance | 0.4 | 0:0.1:2 | Extra room added to the diameter (mm). 0.3-0.6 suits most printers

Pipe / Tube | snap_opening | 0.86 | 0.6:0.01:0.98 | Mouth width as a fraction of the pipe diameter. Lower = tighter snap

Clip Body | wall | 3 | 1.6:0.2:8 | Ring wall thickness (mm). Thicker = stiffer snap

Clip Body | clip_width | 15 | 6:1:60 | Clip width along the pipe (mm); this is the print height

Clip Body | base_thickness | 3 | 2:0.5:30 | Base thickness between wall and pipe (mm)

Mounting | mount_style | "both" | center:Center screw driven through the mouth, tabs:Two side screw tabs, both:Center screw + side tabs, none:No holes (glue or tape) | How the clip is fixed to the wall

Mounting | screw_diameter | 4.2 | 2:0.1:8 | Screw shank hole diameter (mm)

Mounting | head_diameter | 8 | 4:0.5:16 | Screw head diameter (mm), used for the center-screw counterbore

Mounting | head_recess | 2.5 | 0:0.5:6 | Screw head height recessed below the pipe seat (mm)

Mounting | tab_length | 10 | 6:1:30 | Length of each side tab (mm)

Presets

  • pipe-clip-snap-mount_16mm-conduit.stl: {"pipe_diameter": 16, "mount_style": "tabs", "clip_width": 12} - 42 x 18 x 12 mm

  • pipe-clip-snap-mount_half-inch-pvc-21.3mm.stl: {"pipe_diameter": 21.3} - 48 x 23 x 15 mm

  • pipe-clip-snap-mount_3-4in-pvc-26.7mm.stl: {"pipe_diameter": 26.7} - 53 x 27 x 15 mm

  • pipe-clip-snap-mount_1in-pvc-33.4mm.stl (hero): {"pipe_diameter": 33.4, "wall": 3.4, "clip_width": 18} - 61 x 32 x 18 mm

  • pipe-clip-snap-mount_1-25in-pvc-42.2mm.stl: {"pipe_diameter": 42.2, "wall": 4, "clip_width": 20} - 71 x 40 x 20 mm

Licence

Licence: Creative Commons Attribution 4.0 International (CC BY 4.0), https://creativecommons.org/licenses/by/4.0/. You may print, remix, share and sell prints and remixes, including commercially, as long as you give attribution (credit Maker Hollow Studio and link to this design).

Tagi