Coralboard SL Modular Case with 3 Top Panels & Tilting Stand
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Modular, tool-free Coralboard SL enclosure with swappable top panels, camera mount option and tilting desk stand.
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 0
- Wydruki
- 0
- Wyświetlenia
- 37
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Electronics
- Licencja
- Creative Commons — Attribution — Noncommercial
Design goals

Printability first: every part prints flat and without supports on any standard FDM printer, in PLA or PETG, with no special tools or hardware required.
Modular and tool-free: a few simple parts snap together, so the enclosure can be assembled, opened and modified in seconds.
Full access to the board: ports, connectors, LEDs and airflow remain usable, and the top panel can be swapped for the task at hand.
One system, many setups: the same enclosure works on a desk, in a tilting stand, with a camera, or on a custom wall mount.
Design language
Clean, flat-panel geometry with a technical look.
Description
A modular, tool-free enclosure for the Synaptics Coralboard SL with three interchangeable top panels and a tilting desk stand. Everything prints flat without supports and needs no extra hardware, so you can go from a bare board to a protected setup or a ready-to-use smart camera with just a few quick prints.
Main features
Enclosure
Modular, tool-free assembly.
The base, top and side panels snap together with friction-fit features, so individual parts can be removed or replaced without dismantling the whole enclosure. This also makes testing and prototyping easy.Four printed, unthreaded pins (similar to M3x12 countersunk screws) go through the base panel and the Coral board's mounting holes into the top panel. They hold the Coral board in place.
Friction-fit features hold the base, top and side panels together, which is sufficient for a stable assembly in most cases. If the fit is loose (depending on your printer's tolerances), replace the pins with M3x12 countersunk screws for a stronger hold.
All important board interfaces stay accessible through dedicated cutouts, including the CSI and DSI connectors.
The side panels are separate parts, printed flat. This gives clean, precise openings around the connectors.
Hexagonal vents in the top panel allow airflow over the board.
The optional "Coralboard" lettering consists of two separately printed parts that are glued onto the top panel. No multi-material printing is required.
Three status LEDs are routed to the top panel through light pipes made from pieces of transparent 1.75 mm filament. Translucent filament may also be used for the front side panel for an even better view of the LEDs.
Top panel variants
Three interchangeable top panels are available:
Closed: for general use.
Connector cutouts: openings for the board connectors (20-pin GPIO header, I3C, battery, CSI).
Camera mount: mount for an OV5640 camera module with a lens hood.
Tilting stand
A separate desk stand holds the enclosure at an adjustable angle (for example for the camera variant).
The base panel has four keyhole slots. The stand's X-shaped bracket has four printed pegs that slide into the slots. No tools or screws are needed, so mounting and dismounting the enclosure is quick and easy.
A tilting joint with a printed knurled screw and knurled nut lets the enclosure be tilted and locked in position.
The stand has an H-shaped foot frame with a mounting block for the arm.
Other mounting options
Wall mounts or custom brackets can interface with the base panel's keyhole slots.
Printing
All parts are designed to be printed without supports. PLA or PETG is recommended.
For best results, print the base, top and side panels flat.
Print all parts with a layer height of 0.2 mm, except for the knurled screw and knurled nut of the tilting joint, which should be printed with a layer height of 0.1 mm or finer.
The tiny parts (pins and pegs) should be printed separately with a brim or raft to ensure proper adhesion and prevent them from being knocked over during printing.
The two lettering parts should also be printed separately. If you do not have a multi-material printer (like me), add a color change at layer height 0.4 mm.
The supplied 3mf file contains all the parts arranged for optimal printing, including the color change for the lettering parts, which are placed next to a small wipe tower.
Assembly
Enclosure assembly
Insert the printed pins into the base panel. As mentioned earlier, you can replace the pins with M3x12 screws for additional stability if needed.
Place the Coralboard onto the base panel, aligning its mounting holes with the pins.
Insert the light pipe pieces for the status LEDs into their respective slots in the top panel. The light pipes should end just above the LEDs to ensure proper light transmission.
Snap the side panels and the top panel of your choice together using the friction-fit features.
Optional: Glue the Coralboard lettering parts onto the top panel with a tiny bit of super glue. The label positioning aid may help you align the parts correctly.

Tilting stand assembly
Seat the arm in the slot in the H-shaped foot frame.
Insert the four printed pegs into the outer holes of the X-shaped bracket. Orient each peg with its wide head on the outside of the bracket. Make sure to not fully insert the pegs.
Leave some clearance for sliding them into the keyhole slots of the base panel later.Align the pivot hole in the arm with the holes at the center of the bracket. Pass the knurled screw through the joint and tighten the knurled nut on the opposite side.
Slide the pegs into the keyhole slots of the base panel.
Tilt the enclosure to the desired angle, then tighten the knurled nut to lock it in position.

Disclaimer
This is an unofficial, community-made accessory. It is not affiliated with, endorsed by, or sponsored by Synaptics or Google. "Coralboard", "Synaptics" and "Coral" are trademarks of their respective owners and are used here only to identify the compatible product. The license of this design covers only my own work, not any third-party names or marks.