1 / 6
Faceted spiral vase with engraved diamonds and six hanging tabs (vase mode, 14 g) — zdjęcie 1
1 / 6

Faceted spiral vase with engraved diamonds and six hanging tabs (vase mode, 14 g)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Single-wall vase for spiralize/vase mode. 90mm tall, 65mm across the tabs, 18 sunken faces each with an engraved diamond

Ocena
0 / 5
Polubienia
0
Pobrania
0
Wydruki
0
Wyświetlenia
1
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Home Decor
Licencja
Creative Commons — Attribution

Faceted vase designed from the ground up for spiralize mode: one color, one continuous wall, one closed contour per layer, nothing leaning more than 45 degrees outward. Inspired by a ceramic vase with painted concentric diamonds; here the paint became relief.

Shape. The body is the intersection of three hexagonal frustums. One narrows upward and sets the neck, one widens upward and is rotated half a face so its faces cut the corners of the other two (that is where the diamonds come from), and a third flares fast and only cuts near the base to give the vase its foot. Each of the 18 faces is sunk 3 mm toward its center, and a single V-groove diamond is engraved in the middle of each face at 0.30 of the face size. The faceting and the groove read by shadow, so the vase looks different depending on the light.

Ribs and tabs. Six ribs start at the top point of the middle diamonds and widen toward the rim, where they open at 45 degrees into small tabs, 10.5 mm out from the rim. The tabs are for gripping or hanging. Each tab has a conical mark on both sides, 2.5 mm below the rim, as a guide for a 2 mm drill. The holes are not in the model on purpose: in vase mode a hole creates extra contours and the slicer strings plastic across the mouth (checked in the Cura layer preview). Drill after printing if you want to hang it.

Dimensions. 90 x 65 x 62.4 mm in the model. The printed part measures 89.6 mm tall, 63.6 mm across the tabs and 58.1 mm across the body at 55 mm height. Mouth 44 mm, base 50 mm between corners.

Printing

Print as the STL comes, flat on the bed, no scaling, no rotation.

- Ender-3 V3 KE, 0.4 mm nozzle, PLA 1.75 mm

- Spiralize Outer Contour on, Smooth Spiralized Contours on

- 0.2 mm layers

- Outer wall line width 0.6 mm (the vase in the photos); 0.8 mm gives a stronger and more watertight wall and prints without warnings on a 0.4 mm nozzle

- Bottom 1.0 mm (5 layers), 0 top layers, 0% infill

- 200 C nozzle, 60 C bed, fan 100% from layer 3

- Wall speed 40 mm/s; in practice the 8 s minimum layer time sets the pace

- Minimum layer time 8 s so the tabs cool before the next layer

- Initial Layer Horizontal Expansion -0.1 mm to keep the points of the base star sharp

- Skirt, no brim, no supports, Z hop off

- Cura estimate: 1 h 09 min, 4.77 m of filament, 14 g. The printed vase weighs 14 g.

Notes

- A single 0.6 mm wall is not guaranteed watertight. Use it as an outer pot with a plastic liner, or for dry flowers. No drainage holes.

- The ribs and tabs are hollow and open to the inside, as everything printed in vase mode is. The drilled holes hold the empty vase, not weight.

- With a 0.6 mm line the engraved diamond comes out softer than in the model.

- Made for a 3D design and printing course in a computer engineering master's program.

Tagi