1 / 12
Self-Spelling Ouija Board : turn the crank and the ghost spells B-O-O — zdjęcie 1
1 / 12

Self-Spelling Ouija Board : turn the crank and the ghost spells B-O-O

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Turn the crank and the planchette spells B-O-O by itself. Hidden cam and magnets, no electronics.

Ocena
0 / 5
Polubienia
0
Pobrania
0
Wydruki
0
Wyświetlenia
6
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Public Domain

Self-Spelling Ouija Board - turn the crank and the ghost spells B-O-O

Summary

A crank-powered automaton: turn the handle and the planchette glides across the board by itself, stops on B, O, O... and drifts back to GOODBYE. No electronics - a hidden double-groove cam and two levers move a magnet under the board.

Description

Turn the crank. Something under the board answers.

The planchette sits on GOODBYE. Two turns of the crank later it has slid - all by itself - to B, then O, stepped off and come back to O again, and drifted home to GOODBYE. Nothing touches it from above: the "spirit" is a magnet carriage hidden under the 3 mm board.

How it moves

- Crank -> crown wheel & lantern pinion. The handle turns an old mill-style peg gear (12 pegs / 6 rungs), so two crank turns = one full séance.

- One cam, two grooves. The crown wheel carries a single cam disc with a groove on each face. The top groove is the planchette's left-right movement, the bottom groove its up-down movement.

- Two levers. A follower pin in each groove rocks a lever (about 1:2.5 / 1:3 magnification), so a small cam moves the planchette across the whole alphabet.

- Cross slides + magnets. The levers push an X-bar and a Y-bar that cross like a plotter. Where they cross, a carriage with two magnets drags the planchette's two magnets (its eyes!) across the board.

- Gothic windows in the front of the box let you watch the cam, levers and gears do the haunting.

The motion is designed so the planchette stops dead on each letter (dwell sections in the cam), and the cam grooves were checked for undercut and pressure angle (max 45° on the levers). The full cycle was checked for collisions in CAD at 5° steps.

What's in the box (printed)

Hardware

- 1x M8x55 hex bolt + 1x M8 thin nut (DIN 439) - the cam spindle

- 1x M4x20 bolt + M4 nyloc nut - X-lever pivot

- 4 mm steel dowel pins: 3x 4x10, 1x 4x20, 1x 4x30 (or cut from 4 mm silver steel / a 4 mm drill shank)

- 4x disc magnets 8x2 mm (N42-N52): 2 in the carriage, 2 in the planchette - opposite poles facing

- 1x M2x8 screw (carriage clip), 2x M3x10 self-tapping screws (bracket)

- 2x 3x6 mm pins (or 1.75 filament pieces) to align the cam halves

- 3 small felt pads for the planchette, a little dry PTFE lube for the grooves and slots

Print settings

All STLs are already rotated into print orientation (Z-up, sitting on the bed) - just drop them in.

- 0.2 mm layers, 3 perimeters, 15-20 % infill (cam halves, levers, crown: 4 perimeters / 40 %). PLA or PETG.

- Board: print face-down (artwork on the print sheet). Load OB-15 + OB-15a/b/c together as one multi-part object and give each inlay its own filament (MMU/AMS) - the inlays are only the first 0.6 mm, so with a single nozzle you can also swap colour or paint-fill the pockets instead.

- Cam halves: each with its groove facing up (flip OB-04a). No supports.

- Box: upright, no supports (window arches are 45°, wall grooves are short overhangs).

- Lantern shaft: standing on the D-flat end (45° cone under the flange, no supports) - use a brim, it's 115 mm tall.

- Carriage: cap down. Clip, levers, bars, crank, feet: flat as exported.

- Planchette: flat side down; eyes in black (colour change at the top 1 mm, inlay OB-16a, or a marker).

Assembly (about 30-40 min)

1. Glue the feet in. Epoxy the M8 thin nut into the hex pocket under the floor - don't fit the bolt yet.

2. Push the lantern shaft through the pillow block and then the right wall from inside (the collar stops at the pillow block), fit the crank arm on the D-flat.

3. Slide the crown wheel/tube in along the floor from the left, with one peg pointing at the lantern so it slips between the two lowest rungs, and set it on the round boss.

4. Screw the M8x55 bolt up from below through the nut into the tube - this is the spindle. Epoxy the bolt into the nut so it stands rigid.

5. Press the 4x10 pivot dowel into the post and fit the Y lever on it (follower pin up). Glue the cam halves back-to-back with the alignment pins and slide them onto the hex - the Y lever's pin goes into the bottom groove.

6. Screw the bracket to the front wall; fit the X lever on the M4 pivot (follower pin into the top groove).

7. Fit the carriage into the X-bar slot and screw the clip on from below. Magnets into the carriage.

8. Y bar: drop it in - its end tongues sit in the rebates of the side walls and the Y lever's tall pin goes into its short slot.

9. X bar: drop it in - tongues into the front/back wall rebates, the X lever's pin into the slot in its arm, the carriage pin into the Y-bar slot.

10. Lay the board on top (its lip locates it and holds the X bar down) and put the planchette on GOODBYE - its magnets must attract the carriage magnets. Turn the crank.

Tips

- Turn slowly at the letters - the cam has dwells built in, it's meant to feel like a séance.

- If the planchette lags behind, use stronger magnets or add felt/PTFE pads under it.

- Keep steel screws away from the carriage magnets.

Happy haunting! 👻🎃

Tagi