1 / 4
W1SFR "Fat Boy" Single-Lever Paddle Dust Cover — zdjęcie 1
1 / 4

W1SFR "Fat Boy" Single-Lever Paddle Dust Cover

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Dust cover for the W1SFR Fat Boy torsion bar paddle. Arched front leaves the lever free, so you can send with it on.

Ocena
0 / 5
Polubienia
0
Pobrania
0
Wydruki
0
Wyświetlenia
16
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Overview

A dust cover for the W1SFR "Fat Boy" Torsion Bar Cootie/Paddle. It sits on the top face of the stainless base and covers the brass mechanism, contacts and torsion mount. An arched opening in the front lets the lever and Lexan fingerpieces stick out, so the key stays usable with the cover on. The callsign on top is a flush two-color inlay, not a recess, so the top stays flat and easy to wipe.

On the Air

Brass contacts and a torsion bar don't need shack dust, cat hair or a dropped pencil. This cover lets the Fat Boy stay on the desk and stay ready: pull it off to adjust, or leave it on and send. It rests on the base itself rather than the desk, so it rides along if you nudge the key, and the skirt stops above the rubber feet so it never lifts the paddle.

Print Settings

- Printer: Bambu Lab, 0.4 mm nozzle (model not specified)

- Body: PETG-CF, chosen to hide layer lines on the large flat faces. Use a hardened nozzle for CF filaments.

- Callsign inlay: gold PETG, applied as a modifier part

- Layer height: 0.2 mm

- Infill: 10% Gyroid

- Supports: none required

- Orientation: upside down, top face on the plate. The inlay prints in the first 5 layers, and every overhang (rim gussets, front arch) is self-supporting.

The 3MF opens in Bambu Studio with the cover on filament 1 and the callsign as a modifier on filament 2. If the modifier comes in as a normal part, load the cover STL, then right-click > Add modifier > Load and pick the callsign modifier STL. Both STLs share the same coordinates, so it drops in place.

Hardware and Assembly

No hardware required. Set it over the paddle from above, with the arch at the front and the slot in the back rim over the torsion mount. It may be a bit loose to allow for differences in baseplates - simply scale the X/Y dimensions to adjust for a tighter fit.

Design Notes

- Fits a base measured at 75 W x 74 D x 13 mm on 6 mm rubber feet. W1SFR lists the base as 3 in x 3 in, so measure yours. If the fit ring binds, raise base_w and base_d in the OpenSCAD file.

- 1.5 mm clearance per side, 2.0 mm walls, 2.5 mm roof, 3 mm of air above the torsion mount. Outside size is 82 x 81 x 50.5 mm.

- The inner rim is a 4.5 mm shelf that rests on the base top (3 mm of contact) along the back and both sides. Each side rim stops short of the front thumbscrews. There is no front rim, because there's no wall above the arch to hang it from, and the long side rims keep the cover steady.

- A 12 mm slot in the back rim clears the 7 mm torsion mount.

- The front arch is 30 mm wide, centered, and runs to the bottom of the skirt, so the lower right drop-down on the current fingerpiece clears.

- The skirt stops 6 mm above the desk, level with the bottom of the base plate. No cord cutout is needed at that height.

Files included

- Cover 3MF (Bambu Studio, callsign as a modifier)

- STLs: cover body, callsign modifier, fit ring

- OpenSCAD source: change the callsign (call_txt), base size, clearance and depth of the inlay

- Fit ring 3MF: a 20.5 mm slice with the skirt, rims and front arch. Print this first to check fit before the full cover.

Makes, remixes and fit reports are welcome.

Tagi