Cat Flap for Interior Doors 38–42 mm – Telescopic Frame, Ball-Bearing Hinge, Magnetic Latch
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Fully printed cat flap for doors 38–42 mm thick: telescopic two-part frame, 608 ball-bearing hinge, magnetic self-centri
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 2
- Wydruki
- 0
- Wyświetlenia
- 22
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Pets
- Licencja
- Creative Commons — Attribution
A fully printed cat flap for interior doors between 38 and 42 mm thick. Cut a 165 × 165 mm square opening into the door, push the two frame halves in from both sides, tighten four M5 screws, done. The flap swings freely ±90° on two 608 ball bearings and is pulled back to centre by two pairs of magnets, so it closes quietly in both directions without a stop. The outside shows a clean 215 × 215 mm plate with no visible screws: the screw heads sit 5 mm deep and are covered by printed caps.
In use on an interior door in our house since August 2026 (two cats, no complaints). Interior use only: the flap has 1 mm gaps around it and no brush or rubber seal, so it is not draught- or weather-tight. For an exterior door you would need to add a seal and a lock; the parametric source makes that possible, but this version is not designed for it.
How it works
Telescopic frame. The two halves overlap at the middle of the door. The same parts fit any thickness from 38 to 42 mm; a 1.6 mm sleeve on the inner frame covers the joint. No measuring, no shims.
Hinge. Two 608 bearings (8 × 22 × 7, the skateboard kind) sit in half-shell seats in the side columns, clamped between the frame halves. The printed axle pins press into the bearing inner race and the flap knuckle.
Magnetic latch. Four Ø10 × 2.5 mm disc magnets: two slide into slots in the flap rib and are locked with a printed retainer (no glue), two sit in closed pockets in the lower frame fill. Resting gap 2.7 mm. The magnets act sideways, so the flap is centred from both directions.
Hidden hardware. M5 nuts slide sideways into hexagonal pockets in the inner frame (covered by the door once installed); the inner plate is fully closed. Screws go in from the outside and are capped.
Clear opening: 134 × 149 mm over the full door thickness.
Bill of materials (besides the printed parts)
2 × ball bearing 608 (ZZ or 2RS)
4 × M5 × 30 socket head cap screw (DIN 912)
4 × M5 hex nut (DIN 934, the standard 4 mm high one, not nyloc)
4 × disc magnet Ø10 × 2.5 mm (N35 or stronger)
Printed parts
Frame outer (1×): visible face down, 215 × 215 × 26 mm, no support, skirt only
Frame inner (1×): visible face down, 215 × 215 × 32 mm, no support
Flap (1×): on its long edge as exported, 134 mm tall on a 20 mm footprint, use a 5–8 mm brim
Axle pin (2×): standing; or use an 8 mm steel rod, 27 mm long
Screw cap (4×): flat side down
Magnet retainer (2×): flat
Printed in PETG at 0.2 mm, 3 perimeters, 15 % gyroid. All remaining overhangs are bridges ≤ 10 mm, no support needed anywhere. Fits a 250 × 210 mm bed; plate 1 of the 3MF puts the small parts inside the frame opening, plate 2 is the inner frame.
Clearances are 0.2 mm (bearing seats, magnet pockets). The axle pin is Ø8.1 in the Ø8.0 bearing bore on purpose (press fit); sand lightly if it is too tight rather than changing the clearance parameter.
Assembly
Push the magnets into the flap slots (check polarity against the frame magnets first), then push in the retainers.
Press the axle pins into the flap knuckle, bearings onto the pins.
Slide the four M5 nuts sideways into the hex pockets of the inner frame, corner first, until they stop.
Lay the flap with its bearings into the half-shell seats of the outer frame, drop the frame magnets into their pockets.
Outer frame into the door from one side, inner frame from the other.
Four M5 × 30 from the outer side; they pick up the nuts.
Press the caps into the countersinks.
Remix it
The FreeCAD 1.1 source (cat-flap_freecad-source.FCStd) is fully parametric via the Parameters spreadsheet: door_thickness, brim (frame size = opening + 2 × brim), flap_gap_bottom (magnet strength), print_clearance, magnet_x, screw_column_width. STEP files of every part and of the complete assembly (with screws, bearings and magnets as reference bodies) are included for other CAD tools. The notes file (German, .txt) describes every dimension and the revision history.
Designed in FreeCAD together with Claude (Anthropic): four revisions, three test prints.
License CC BY 4.0: print it, sell it, change it, just name the source.
