Weatherproof Outdoor Enclosure 70 × 80 × 40 mm – No Gasket, Drip-Edge Design (ASA)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Wall-mounted outdoor box for small electronics that keeps rain out by geometry alone: drip channel, overhang, 45° lid ch
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 1
- Wydruki
- 0
- Wyświetlenia
- 14
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Electronics
- Licencja
- Creative Commons — Attribution
A wall-mounted outdoor enclosure for small electronics that keeps rain out by geometry alone: no gasket, no O-ring, no silicone. Two printed parts, body and lid, printed in ASA.
I use it for a 24 V → 12 V DC-DC converter (DFRobot DFR0205) that powers the heater of an Ecowitt WS90 weather station, but there is nothing WS90-specific about it. Inside you get 70 × 80 × 40 mm plus two triangular pockets at top and bottom, four Ø6 standoffs on a 39 × 44 mm grid (M3 self-tapping) for a PCB, and three cable entries through the bottom. Change the inner dimensions, the PCB hole pattern or the cable diameters in the spreadsheet and rebuild.
How it stays dry
The water concept follows Slant 3D's video "This Box Keeps Out Water Without a Seal":
Hexagonal outline. Vertical sides, a flat 12° roof with a ridge at the top, a V with a low point at the bottom. Water on the lid runs to the sides, water at the bottom runs to the centre.
Drip channel in the frame. The 10 mm frame is split into an inner wall, a 6.4 mm channel and an outer wall. The inner wall stands 5 mm higher and has an overhang with a 45° underside reaching to the middle of the channel.
Lid with 45° chamfer. The lid ring rests on the outer wall; the inner chamfer, the overhang and the channel form the arrow-shaped cross section from the video. Water that passes the lid seam lands in the channel, runs down the sides and leaves through a 6 mm notch at the low point. To get inside it would have to climb over the overhang.
Cable entries point straight down through the V: one Ø3.8 mm and two Ø6.8 mm holes with 0.5 mm clearance.
Mounted with two countersunk 4.5 × 50 screws from inside through the back wall (in the triangles, where the PCB needs no room). The lid is held by friction on an inner frame; lid_plug_gap in the spreadsheet tunes the fit.
Dimensions: inside 70 × 80 (+ 7.4 mm triangles) × 40 mm; outside 90 × 115 × 45 mm, 53 mm deep with the lid. Body 108 cm³, lid 28 cm³.
Printed parts
Body: back wall down, 90 × 115 × 50 mm, no support
Lid: front down, 90 × 115 × 7.4 mm, no support
Both parts come twice: plain, and with built-in mouse ears on all six corners (0.2 mm discs with a 1 mm neck, snip off after printing). Use the mouse-ear version for ASA or ABS; for PETG the plain one is fine. The 3MF files have body and lid arranged on one 250 × 210 mm plate.
Print settings I use: ASA, 0.2 mm, 2 perimeters, 15 % gyroid, 5 top / 4 bottom layers. The walls are exactly 1.8 mm = 2 × 2 perimeters of 0.45 mm, and the skins are designed so that the default top/bottom layer count makes them solid; you do not need 100 % infill. ASA on a large flat part needs a warm chamber, a clean PEI sheet and an adhesive; that is normal and not specific to this model.
Design for printing
Back wall and lid plate are not solid slabs. They are a 0.8 mm continuous coat on the bed side with 1.6 mm tiles on top, separated by 1 mm grooves on the inside, plus a groove around the foot of the walls. The idea (again from Slant 3D) is that no long stretch of plastic can shrink as one piece and lift the corners. The frame between inner and outer wall is hollow on the sides and roof; the V stays solid for the cable holes and the drain. Details, with section renders, in the included notes.
Remix it
The FreeCAD 1.1 source (outdoor-box_freecad-source.FCStd) is parametric via the Parameters spreadsheet. The three dimensions you have to set are inner_width, inner_height and inner_depth; everything else (frame, channel, lid, holes, chamfers) follows. The included Python build script rebuilds the whole model from the parameters (freecadcmd -c "exec(open('ws90-power-box-v3_build.py').read())"), which is the safe way to change the PCB grid or the cable holes. STEP files of body and lid are included for other CAD tools. Notes in German (.txt).
Designed in FreeCAD together with Claude (Anthropic).
License CC BY 4.0: print it, sell it, change it, just name the source.
