Female-to-Male Thread Adapters: G 1/4" to G 1"
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Twenty female-to-male G (BSPP, ISO 228) adapters, every combination from G 1/4" to G 1". Prints without supports.
- Ocena
- 0 / 5
- Polubienia
- 16
- Pobrania
- 82
- Wydruki
- 0
- Wyświetlenia
- 236
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other House Equipment
- Licencja
- Standard Digital File License
Female-to-male adapters for BSP parallel threads (G, ISO 228) from G 1/4" to G 1", in every combination: 10 reducers and 10 enlargers. Typical uses are garden hoses, taps, pumps and rain barrels.
Please don’t scale the parts. The threads follow ISO 228 and are made to fit standard fittings.
These adapters are not compatible with NPT threads.
Have fun!
Also available:
Update
Outer hex instead of internal hex: The wrench now sits on the female sleeve.
Full flow: The bore no longer narrows for a hex key.
Strength check: Six enlargers got a larger hex, and the bore is limited where strength requires it.
Adapters
Read the arrows from female to male.
Group (female) | Adapter | Wrench size | Min. bore |
|---|---|---|---|
G 1/4" | G 1/4" → G 3/8" | 19 mm | 7.0 mm |
G 1/4" → G 1/2" | 19 mm | 7.0 mm | |
G 1/4" → G 3/4" | 22 mm | 7.0 mm | |
G 1/4" → G 1" | 27 mm | 7.0 mm | |
G 3/8" | G 3/8" → G 1/4" | 22 mm | 6.2 mm |
G 3/8" → G 1/2" | 22 mm | 10.0 mm | |
G 3/8" → G 3/4" | 24 mm | 10.0 mm | |
G 3/8" → G 1" | 30 mm | 10.0 mm | |
G 1/2" | G 1/2" → G 1/4" | 27 mm | 6.2 mm |
G 1/2" → G 3/8" | 27 mm | 9.7 mm | |
G 1/2" → G 3/4" | 27 mm | 14.5 mm | |
G 1/2" → G 1" | 30 mm | 14.5 mm | |
G 3/4" | G 3/4" → G 1/4" | 32 mm | 6.2 mm |
G 3/4" → G 3/8" | 32 mm | 9.7 mm | |
G 3/4" → G 1/2" | 32 mm | 13.3 mm | |
G 3/4" → G 1" | 36 mm | 19.0 mm | |
G 1" | G 1" → G 1/4" | 41 mm | 6.2 mm |
G 1" → G 3/8" | 41 mm | 9.7 mm | |
G 1" → G 1/2" | 41 mm | 13.3 mm | |
G 1" → G 3/4" | 41 mm | 18.9 mm |
Flat washers
You need one washer for each female thread: one on the floor of the adapter’s female thread and one in the fitting that takes the male thread.
Thread | Washer (OD × ID × thickness) | Max. washer OD in adapter |
|---|---|---|
G 1/4" | 11 × 6 × 1.5 mm | 12.0 mm |
G 3/8" | 14 × 8 × 1.5 mm | 15.6 mm |
G 1/2" | 18.5 × 12 × 2 mm | 19.3 mm |
G 3/4" | 24 × 17 × 2 mm | 24.8 mm |
G 1" | 29 × 18 × 2 mm | 31.0 mm |
Recommended Material
Part | Material |
|---|---|
Adapter | PETG, ASA, ABS |
Print Settings
Setting | Value |
|---|---|
Layer height | 0.15 mm |
Perimeters | 4 |
Top / bottom layers | 5 |
Supports | None |
Infill | 40% or more |
Part cooling fan | Low (max. 30%) for good layer adhesion |
Print Orientation
Part | Orientation on the bed |
|---|---|
Adapter | Upright, male thread down |
Use
Place a flat washer in the female fitting that takes the male thread.
Screw the male thread in by hand. Tighten with the wrench on the hex, max. 1/4 turn.
Place a flat washer on the floor of the adapter’s female thread.
Screw the other fitting into the female thread by hand until the washer seals.
Don’t use thread tape on the end faces. These adapters seal against the washer, not in the thread.
Safety note:
Printed adapters are meant for low-pressure water such as garden hoses, rain barrels and pumps.
Don’t use for gas, hot water, drinking-water installations or permanent mains pressure.
Don’t over-tighten: a long wrench can twist off any plastic adapter.