Sport Bike Kit - Superbike-Style Motorcycle with Working Steering, Spinning Wheels & Side Stand
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A 1:10 superbike-style motorcycle kit with working steering, spinning wheels and a side stand. No glue.
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 10
- Wydruki
- 0
- Wyświetlenia
- 47
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Vehicles
- Licencja
- Creative Commons — Attribution — Noncommercial
A modern superbike-style motorcycle you build yourself, at about 1:10 scale (200 mm long, 100 mm tall). An original design with no brand logos.
WORKING PARTS
The inverted fork steers, with a natural steering lock at about 30 degrees each way
Both wheels spin: 5 split-spoke cast rims with twin drilled front discs, a rear disc and a sprocket
The side stand folds down to park and swings back up
DETAILS
A twin-spar beam frame with an inline-four engine, cooling fins, exhaust headers and collector, a radiator and a mono-shock
A nose cowl with twin headlights, a central air intake and a windscreen area ready to paint smoke-black
Side fairings with race-number ovals, and a tank / seat / tail unit with a fuel cap and tail light
An inverted fork with radial calipers, clip-on bars and a dash
A braced swingarm and a short side silencer
Everything is printed: no glue, screws or springs. Parts plug together with printed pins and pegs
PRINT SETTINGS
The 3MF is ready to print with 4 plates: 0.16 mm layers for large parts, 0.12 mm for rims and small parts, 0.4 mm nozzle, 3 walls, 15% gyroid infill, no supports
Pins, axles, washers and side stand: 100% infill (already set in the 3MF)
Detect thin walls is ON for the fine details
Plates are grouped by colour: chassis (white), bodywork (gold), rims and pins (white) + tyres and fenders (swap to black), fork/swingarm/silencer (gold)
TPU tyres work great, PLA works too
About 100 g of filament. Largest part 119 x 77 mm, fits any common printer
ASSEMBLY
Chassis + fork: lay the left chassis half inside up, lay the fork's steering stem into the half head tube (bottom clamp below, top clamp above), push 5 joining pins in and press the right half on. The fork is now captured and steers.
Swingarm: open its arms slightly and snap the pivot holes over the two pivot pegs behind the engine.
Wheels: push two rim halves into each tyre (front: two disc halves; rear: sprocket half left, disc half right). Front wheel between the fork legs with the short axle pin; rear wheel between the swingarm arms with a washer each side and the long pin.
Front fender: hold the halves together over the tyre and spread the fork legs slightly so the pegs click into the fender.
Side panels: press each onto the 3 pegs on its side of the engine. Nose cowl: lower it onto the two pegs at the front of the panels.
Tank / seat / tail: pin the halves together (3 pins) and press onto the frame and subframe pegs.
Silencer: press onto the peg under the engine, on the right. Side stand: clip onto the peg on the left.
TIPS
Pin or peg too tight? Sand it lightly. Joining pins loose? Print them at 103%
Turn the bars gently: the steering stops on its own at about 30 degrees
Original design by Kirimas Studio.