1 / 2
8-Slot SD Card Organizer with Rear Storage Tray — zdjęcie 1
1 / 2

8-Slot SD Card Organizer with Rear Storage Tray

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

One-piece SD card rack with eight slots, a rear storage bin and finger cut-outs. Editable OpenSCAD source.

Ocena
0 / 5
Polubienia
0
Pobrania
2
Wydruki
0
Wyświetlenia
11
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Organizers
Licencja
Creative Commons — Attribution

A one-piece organizer for eight full-size SD cards, with a separate rear compartment for loose cards or small accessories. The open comb guides leave the card tops accessible. Finger cut-outs and an internal rear ramp help remove items from the tray. No assembly or additional hardware is required.

DIMENSIONS AND FIT

Outside width × length × height: 47 × 152 × 26 mm. Eight slots at 10.5 mm pitch; each slot is 24.8 mm across with a 2.9 mm thickness gap. Designed for nominal 24 × 32 × 2.1 mm full-size SD cards, with 0.4 mm clearance per side. Rear compartment: 43 × 62 mm inside. Base: 2.4 mm. Nominal loaded height with cards upright: 36.4 mm.

For full-size SD/SDHC/SDXC cards or full-size SD adapters, without protective cases. Bare microSD cards need a suitable full-size adapter. Check your particular card or adapter and your drawer clearance; the slot is a guide, not a locking clip.

PRINTING

PLA, 0.4 mm nozzle, 0.2 mm layers, 3 walls, 15% infill, 4 top and 4 bottom solid layers. Print the flat bottom on the bed, open side up, scale 100%. The geometry is designed to print without supports; check your own slicer preview and use your actual printer and filament profile. After cooling, clear strings from the slots and try one card gently before loading the rack.

ESTIMATES, NOT SLICER OR MEASURED RESULTS

Approximately 45 g PLA / 3 h 15 min; material cost about 18 CZK at 400 CZK/kg. The analytical calculation gives 44.9 g and 193 minutes. Rough scenarios: 36–54 g and 2 h 14 min–5 h 35 min. These are not guaranteed bounds. Actual printers and settings may fall outside the range. No slicer was available for this run.

FILES AND EDITING

Load either SD_vanicka_8.stl OR SD_vanicka_GEOMETRIE.3mf; they are alternative formats of the same single printable part. The 3MF contains geometry in millimetres only, with no printer/material profile, supports, toolpaths or G-code. SD_vanicka_8.scad is the editable parametric OpenSCAD project. The English TXT guide contains printing and editing instructions. The illustrated cards are not included as print parts.

In OpenSCAD, card_count supports 6–9 slots. drawer_width/length/depth specify the drawer interior; drawer_clearance is total clearance, default 1 mm. Card width and thickness clearances are also total values. Render with F6 and export again after editing. Recheck changed geometry; do not scale the entire STL to adjust card fit.

TESTING AND PHOTOGRAPHS

The supplied user photographs show a printed example and sample SD cards. Printer settings, measured dimensions and a full eight-card fit test have not been reported. The photos alone do not validate every slot or printer setup. Software checks: one connected closed manifold STL mesh, correct winding and millimetre dimensions, no degenerate triangles, successful OpenSCAD regeneration, geometry-only 3MF comparison and sampled nominal-card insertion checks in all eight slots. Physical fit still depends on printing and cards.

ORIGIN AND LICENSE

Original AI-assisted parametric OpenSCAD design; not a downloaded remix. License: Creative Commons Attribution 4.0 International (CC BY 4.0). Suggested credit: 8-Slot SD Card Organizer — Tomatoueu, AI-assisted design.

Tagi