Baroque Frame for 50x70 cm Painting (8 Pieces)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Baroque frame for a 50 × 70 cm painting: 8 pieces, hidden pins, no supports, about 807 × 1008 mm. Gold painted by hand.
- Ocena
- 0 / 5
- Polubienia
- 3
- Pobrania
- 17
- Wydruki
- 0
- Wyświetlenia
- 55
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Home Decor
- Licencja
- Standard Digital File License
Baroque Frame for 50x70 cm Painting (8 Pieces)
I was done with plastic pumpkins, so this Halloween I hung a Van Gogh. The frame is baroque, about one meter tall, and it comes off the printer in eight pieces. Hidden pins lock them together, and a 50 × 70 cm painting slides into the groove. I printed every piece in black and painted the gold by hand.

Eight Pieces, One Frame
The whole frame is about 807 × 1008 mm, too big for any print bed. I cut it on a 3 × 3 grid and left the center open, so you print eight pieces in a ring. Each one prints flat on its back with no supports. The pins sit on the back, so from the front you only see a thin line at each joint.

Frame: About 807 × 1008 mm, relief up to 40 mm deep.
Window: 494 × 694 mm. The frame covers 3 mm of the painting on every side.
Painting Groove: 500.6 × 700.6 mm, for a 500 × 700 mm painting up to 1.6 mm thick. The printed painting is 1.2 mm.
Largest Piece: 275 × 339.5 mm with its pins, so you need a bed of at least 340 × 320 mm.
The Painting
The painting is printed too: the part of The Starry Night with the cypress, 50 × 70 cm, printed flat in eight colors. It comes in six panels of 250 × 233.3 mm, two columns and three rows, and they slide into the frame from the bottom.

Gold, by Hand
Every piece prints in black PLA. Then I brushed gold paint on the relief. The black stays in the deep cuts, and the print lines on the carving look like wood grain.

Key Features:
Built-in pins on the back lock every joint. No screws between the pieces.
No supports: the painting groove has a 45° chamfer, so nothing prints in mid-air.
The painting slides in from the bottom, then the bottom bar closes the frame.
Two keyhole slots on the back of the top center piece, ready to hang.
What's in the Files:
3MF: Baroque Frame - H2S 8 Plates.3mf, a Bambu Studio project for the Bambu Lab H2S with one piece per plate.
STL: Baroque Frame - Top Left.stl, Top Center, Top Right, Middle Left, Middle Right, Bottom Left, Bottom Center and Bottom Right, one file per piece.
Painting 3MF: Baroque Frame - Painting H2C Plates 1-3.3mf and Plates 4-6.3mf, two Bambu Studio projects for the Bambu Lab H2C with three panels each in eight colors, one panel per plate.
Printing Recommendations:
0.4 mm nozzle, 0.20 mm layers, 2 walls, 8% infill, no supports. Every piece goes on the bed with its flat back down. The 3MF is set up for the Bambu Lab H2S on the Textured PEI plate, with the corner pieces turned so their 339.5 mm side runs along the 340 mm side of the bed. If you slice the STL files, turn the four corner pieces 90° the same way.
Time and Filament: About 93 hours and 2.7 kg of PLA for the whole frame. Each piece takes 10 to 12.5 hours and 300 to 360 g.
Color: Black, then gold paint by hand. Any color works.
The Painting:
Bambu Lab H2C, 0.08 mm layers, 100% infill, eight colors of PLA Basic: white, cyan, magenta, yellow, black, red, blue and green. About 61 hours and 540 g of PLA for the six panels, 9 to 11 hours and 90 g per panel.
Assembly
Work face up on a large table.
Lay Top Left and Top Right down, then lower Top Center onto their pins.
Lower Middle Left onto the pins of Top Left, and Middle Right onto Top Right. The frame is now an upside-down U.
Slide the painting panels in from the open bottom. Their edges run in the side grooves up to the top one. Top row first, then the middle, then the bottom.
Lay Bottom Left and Bottom Right down, then lower Bottom Center onto their pins.
Push the bottom bar up. Its pins go into Middle Left and Middle Right, and the bottom edge of the painting goes into the groove.
Glue the frame to the backing behind the painting before you hang it. The keyhole slots are on the top piece, and the glue keeps the lower pieces in place. A drop of glue in the pins adds extra hold.
Hanging
Two keyhole slots on the back of Top Center, 160 mm apart and about 40 mm below the top edge. They take screws with a head up to 9 mm and a shank up to 4.5 mm: the head goes into the wide hole and the frame drops 12 mm onto the shank.