1 / 5
Haunted Traveler: a fridge-magnet reversing screw with 9 Halloween riders — zdjęcie 1
1 / 5

Haunted Traveler: a fridge-magnet reversing screw with 9 Halloween riders

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A ghost, jack-o'-lantern or seven more spooks ride a self-reversing screw across your fridge, turning at every reversal.

Ocena
0 / 5
Polubienia
1
Pobrania
1
Wydruki
0
Wyświetlenia
21
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

A little haunted tram for your fridge. A diamond screw with two crossed grooves turns the same way all the time, and the carriage on it runs 60 mm one way, reverses by itself and comes back. The rider on top isn't just a passenger: it turns its head as it goes.

How it moves

  • The rider sits on a short square axle that comes up from the carriage's swivelling shoe. The shoe follows the screw's groove, so the rider turns with it.

  • It's upright at each end, tilts up to 42° as it travels, and swings 83° the other way every time the carriage reverses.

  • Turn the gears one way and it leans into each run. Turn them the other way and it looks back over its shoulder.

Nine riders, swapped in seconds

Every rider has the same square socket in its back and pulls straight off the axle. The socket sits on each rider's centre of mass, so it balances whichever way round you fit it.

Rider

Colours, bottom to top

Change at

Ghost

white, black

9.6 mm

Vampire

white, black

9.6 mm

Jack-o'-lantern

orange, black (green stem, printed separately)

9.6 mm

Black cat

black, yellow

9.6 mm

Skull

white, black

9.6 mm

Spider web

orange, black

9.6 mm

Bat moon

orange or yellow, black, white

8.6 and 9.6 mm

Candy corn

yellow, orange, white

8.6 and 9.6 mm

Mummy

black, white, yellow

8.6 and 9.6 mm

The colours change by layer height, never within a layer. On an MMU3 that's one or two filament swaps for the whole plate, however many copies are on it (the MMU3 projects print six of one rider per plate). On a single-colour printer, add an M600 colour change at the same heights.

The ghost, vampire, jack-o'-lantern and bat moon are printed and riding on my fridge. The black cat, candy corn, skull, mummy and spider web are the newest: they're fit-checked in the model through a full cycle, and I'm printing them next.

Driving it

The kit includes a 32T crank gear on its own magnetic puck, held together with printed screws. Touch its edge to the traveler's 24T input puck and the gears mesh. One stroke takes just over half a turn of the crank. Any driving gear touching the input puck works too. In the photo and GIF, a TOMY Gearation motor turns the crank gear. Not affiliated with or endorsed by TOMY.

On the fridge

It stands on two magnetic pucks (a ferrite ring with grip tape under each), one at each end, and weighs about 120 g. It's 163 × 51 mm, and the riders stand 52–62 mm off the door. Mount it whichever way suits your fridge, then fit the rider upright: the axle is square at both ends, so it goes in any of four ways.

Printing

  • PLA, everything oriented in the files. Everything was printed and tested at 0.20 mm layers. No supports, except inside the input puck's magnet pocket (see the table).

  • Haunted Traveler - single plate.3mf is the whole traveler plus the jack-o'-lantern on one MK3.5 plate, about 64 g. The crank puck is its own plate, Crank puck v1 - printed screws.3mf, about 32 g.

  • Riders are about 5 g and 16–17 minutes each.

  • Crank_Gear_32T is supplied as a .3mf (it's a dense mesh because of its printed thread socket); it's also inside the crank puck project.

Part

Qty

Settings (PLA, MK3.5, 0.4 nozzle, 0.20 mm layers)

Trav_Frame, Trav_Far_Block, Trav_Carriage, Trav_Cap_Pumpkin

1 each

defaults

Trav_Puck_24T, Trav_Tail_Pad

1 each

4 perimeters. On Trav_Puck_24T, add supports inside the magnet pocket only (a support enforcer or paint-on): without them the pocket ceiling sags around the centre post

Trav_Gear_24T_Crown

1

push out the bridge disc in the bore

Trav_Screw

1

upright, outer walls 25 mm/s

Trav_Key_Sleeve

1

defaults

Trav_Peg_Pin, Rider_Axle

1 each

on its flat, 100% infill

Trav_Shoe_Square, Turret_Knob

1 shoe, 2 knobs

defaults

Riders

any

3 perimeters, 12% gyroid, back on the bed, colour change(s) as in the rider table

Pumpkin_Stem

1

3 mm brim (the only part that needs one); glue into the pumpkin

Crank_Puck_32T, Crank_Gear_32T

1 each

puck back down, 4 perimeters; gear flat, crank boss up; pop out the bridge disc in the bore

Crank_Puck_Axle_Screw, Crank_Screw

1 each

lying on their flats, 100% infill

Crank_Handle_v1

1

standing, 4 perimeters

Hardware

  • 2 × M3 × 40 and 2 × M3 nuts (the knob clamps)

  • 2 × M3 × 30 (far block)

  • 2 × M3 × 8 (cap)

  • 1 × 608 bearing and 2 × ferrite ring magnets, 31 × 9.9 × 5.17 mm, for the traveler

  • Crank puck: 1 × 608 bearing, 1 × ferrite ring. Its axle and crank screws are printed, so it needs no metal screws

  • Grip tape discs Ø45.8, Ø31.8 and Ø61.8 (template: grip_tape_puck_discs.svg)

  • Optional: dry PTFE or graphite on the groove and rails

Assembly

  1. Pucks: drop an M3 nut into each hex pocket, glue a ferrite ring into each, and cover the backs with grip tape.

  2. Gear: push out the bridge disc and press the 608 in from below. Set the gear on the input puck's shoulder, then drop the key sleeve through the bearing into the keyed slot.

  3. Peg pin, then screw: press Trav_Peg_Pin into the D-hole in the near block (the flats only fit one way) with a drop of CA, then push the screw's pinion end onto the pin.

  4. Carriage: slide it onto the rails from the far end and park it mid-way.

  5. Shoe: drop Trav_Shoe_Square into the carriage's round hole, tip down, and turn the screw until the tip drops into the groove. Screw on Trav_Cap_Pumpkin with the two M3 × 8, snug only, so the shoe still swivels.

  6. Far block: slip it over the screw's far stub, butt it against the rail ends and fix it with the two M3 × 30.

  7. Check: turn the screw by its pinion. The carriage should run end to end and reverse on its own.

  8. Mount: lower the frame onto the input puck so the crown meshes with the pinion and the far block keys into the tail pad. Press an M3 × 40 head into each knob and screw them down finger-tight.

  9. Rider: drop Rider_Axle down through the cap hole into the square socket in the shoe, any way round. Run the carriage to one end, then press a rider onto the square end in whichever of the four positions puts it upright. If it's loose, print Rider_Axle_tight.

  10. Crank puck: glue the ferrite ring in and cover the back with the Ø61.8 disc. Push the bridge disc out of the gear and press the 608 in from below. Set the gear on the puck and screw the printed axle screw down through the bearing, finger-tight on its wings. Thread the crank screw through the handle into the gear. Push the crank puck against the traveler's input puck until the edges touch.

Tagi