Bottom Fan Floor Tray for Lian Li O11D EVO XL (140 mm fans)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Drop-in tray that fills the empty floor around 3 x 140 mm bottom fans in the Lian Li O11D EVO XL. 13 sizes + Ope
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 0
- Wydruki
- 0
- Wyświetlenia
- 9
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Computers
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Fills the empty floor space around the bottom fans of the Lian Li O11D EVO XL. The front tray covers the floor between the front glass and the first fan, plus the space in front of the motherboard tray. A two-piece strip runs along the side glass beside the fans. The tops sit flush with 25 mm fans.
Inspired by H3D3F's tray for the standard O11 Dynamic EVO. This is a separate design, drawn from scratch for the EVO XL with 140 mm fans.
NOT YET TESTED
I designed this against Lian Li's official CAD model of the EVO XL and checked every size there: at least 1 mm clear of the glass, clips, screws and fans, and every foot lands on the floor. I haven't fitted a printed set in my own case yet. Check the fit before trusting it with your build. I'll update this page once I've tested it.
WHAT'S INCLUDED
- Front tray (L-shaped): 13 sizes
- Side strip, front piece: 13 sizes, to match your tray
- Side strip, rear piece: one size for everyone
- OpenSCAD files for any other size
WHICH FILE
Measure from the inside face of the front glass to the front edge of the first bottom fan's frame. Print the tray with that number. If you're between two sizes, use the smaller one.
- Sizes: 44, 46, 48, 50, 52, 54, 56, 58, 60, 65, 70, 75, 80 mm
- Three fans pushed together on the stock bracket: about 44-55 mm
- Side strip: use the same number for the FRONT piece. The REAR piece is the same for everyone.
WHAT IT ASSUMES
- 3 x 140 mm fans on the stock bottom bracket. The bracket fixes their side-to-side position, so only the front-to-back gap varies.
- 25 mm thick bottom fans. With 28 mm fans the tray sits 3 mm below the fan tops; set bottom_fan_thickness in the .scad to keep it flush.
- Side intake fans up to 28 mm thick. The tray stops 1.5 mm short of them. No side fans? Set side_fan_thickness to 0 in the .scad and the arm grows to fill that space.
- Standard (non-reverse) layout
- 1.5 mm clearance to both glass panels and to the fans
HARDWARE
None. It drops in with no screws, glue or tools.
PRINT SETTINGS
- PLA or PETG
- Print as exported: top face down, feet and ribs up. No supports.
- 0.2 mm layers, 3 walls, 15-20% infill
- A textured plate gives the top a textured finish
INSTALL
1. Turn off the PC, switch off the power supply and unplug the cord.
2. Remove the side glass panel (see your case manual).
3. Route any fan cables first. The tray covers the floor near the front, and its slot sits over the floor's cable holes.
4. Lower the front tray into the front corner.
5. Set the rear strip piece along the side glass, against the rear panel.
6. Drop the front strip piece in from above so its dovetail lands in the rear piece's socket. If the dovetail is tight, sand the tab lightly.
7. Refit the glass, plug the PC back in and power on.
Check the fit in your own case before trusting it with your build. Provided as is; you're responsible for your build.