Liczymy pasujące modele…
Like it? Support me. Website: https://pixelglance.com Buy Models: https://cults3d.com/en/users/PixelGlance Summary This is Vertical Bracket for watercooled GPUs, and is perfectly fitted for the Lian-Li O11DXL-X PC Case. But it has also…
I printed it in PETG with 40% gyroid infill and 4 perimeters and he “rubber interface” in TPU 95A with 2 perimeters and 20% infill. The rubber interface is a nice touch but definetely not required. If you have a round adhesive bumper pad…
On the right side of the Lian Li 011 XL, there is a spot for 3x 120mm fans. After initially assembling, I noticed that all of the wires ran through this location and blocked a lot of airflow. I created this fan duct to almost make contact…
Apollo 11 in 3 parts (shell, inside, top) Apollo11.stl is the shell+inside joined together without top. Apollowhole is just for viewing. Cleaned, solidified, and made printable from Smithsonian 3d scan found on sketchfab. Category:…
I created this STL to help fit my Asus Ryujin ii 360mm radiator in the top of my Lian Li O11D Mini case. By default, this case is not made to support that large of a radiator on top. Lian Li sells a bracket kit to do this very thing but…
This print allows for an O11 Dynamic XL case to be lifted 55mm of the ground. It fits over the existing feet without modifications. The design of the feet allows for just printing the design four times without mirroring. Printed with 20%…
Glass spacer for the Lian Li pc-o11-Dynamic. This design was created to all for horizontal mounting of 3000 GPU's in the Lian Li pc-o11-Dynamic with a water block. Hope it can help someone out! Print Settings Printer Brand: Prusa Printer:…
I remixed this to put it in the O11 Dynamic non XL version. Now there are two fans channeled together in a single duct. The height is matching if you put the fans on the backside of the mounting point of the case (the side with the PSU…
There's a couple commercial options for an airflow focused panel for the o11 Dynamic XL, but they're expensive. Other panels I could find are all for the o11 evo or standard. So I made this, it's designed to fit on a CR10 or similar sized…
Remixed this to replace the original storage that came with the GoPro. This fits GoPro with silicone cover Also added my .3mf files to print if you have a Bambu X1C, or you can just check my PETG settings as i use this for all my boxes…
Higher Feet for O11 Air Mini for improved Airflow. You need 1 set of mirrored and 1 set of regular feet each (Yes the long one is the same for mirrored and regular version ;) ).
Don't want to suck hot carpeted air, dust and dirt into your expensive GPU and case? Want cooler temps and higher airflow? Use these ducts to pull air in from beside the case not directly and immediately beneath it. Position them pointing…
I wrote an article with testing results about this: https://www.igorslab.de/en/o11d-hdd-cooler-2 This is a Remix of Thingi 4923606, but made to fit the regular O11 Dynamic and not the XL Version. Two 60x25mm fans fit inside, I suggest…
This is a magnetic cover for Lian Li O11 mini. Neet to use 20x3mm magnets, use hot glue. If you need something ask :)
Suggest 5-6 walls, 3mm+ top/bottom layers. Infill is moot if your shells are thick enough, so use whatever gives you good results. Supports needed for the holes
I wanted a way to hold my headphones near my PC while not in use. After trying several designs, I ended up desiging this. Pretty Happy with the result. It works very well.
Extended case feet for the O11D to promote airflow. 47mm tall, about twice as tall as the stock feet. Reuses the original (6x) fasteners and (4x) rubber feet. Printed in ABS, .6mm nozzle, with no supports, with the case mating surface…
4 separate risers included in file. Fit under the existing case legs and front IO module (in standard orientation.) Printed in PLA 0.32mm layer height 0.96 wall thickness 20% infill
Lian-Li O11 Dynamic Mini Panel Spacers created to space out side panel approximately 0.5in from case frame. Created for side panel although you can print out the top holder 4x to space out the front panel as well.…
So yeah, troubleshooting random crashes, short version, removed all the vertical graphics card hardware (didn't solve the problem) and wanted something to fill the empty slots that wasn't using all the screws and kept dust out a bit…
Hi there, i designed a cover for the cable management Case: Lian Li O11 dynamic XL Support: From build platform only!! Print Settings Printer Brand: Creality Printer: CR10S PRO Rafts: Doesn't Matter Supports: No Resolution: 0.15 Infill:…
By default, the filter is placed very close to the panel, reducing airflow and increasing noise. This spacer mounts on the existing pins/slots without requiring any glue / adhesive, and adds 6mm of clearance. The model is actually split…
Adapts the 120mm rails for 140mm fans
Added negative cubes to modify the print for ROG edition O11 XL cases. I used the same print settings as recommended in the original. No supports needed. Made in Orca slicer, if that matters.
Moved to Printables from Thingiverse (original here: https://www.thingiverse.com/thing:4923606 ) This is an external HDD fan shroud for the Lian Li O11D XL ATX Computer Case, also known as the O11 Dynamic XL or PC-O11D-XL. The Hard Drive…
Based on the plate from https://www.thingiverse.com/thing:5078920 I designed a holder for Corsair commander pro, light node and RGB fan hub. Fit perfect on Lian Li o11 mini. The photo from cura is for setting the support blocker, you need…
Simple tool for removing the lens of a GoPro Hero11. I only have the 11 but I'm guessing it works with others. The lens dimensions are 32mm x 32mm, so anything with those dimensions should work. Prints easy with no supports. If you like…
This is a modification based on the Lian Li Additional I/O Kit that allows the Startech USB 3.0 Internal Multi-Card Reader to be added to the Lian Li O11 Dynamic EVO case. Remove the metal shell from the Startech card reader and install…
I made a little stand for my Funko Pop Jollibee guy. You could mount pretty much anything on it that's similar size. It sits inside the original Lian Li PC-O11 Dynamic midtower case above the Der Baur badge in the back. The mounting holes…
Vent covers to help direct cold air to components and hot air out of my Lian Li Dynamic Evo computer case. This case has hexagon vent holes and since Lian Li is awesome they share the full CAD model on their page . Ctrl+F and search for ‘…
Halterung für die Corsair XD5 Pumpe im Lian Li PC-O11DX Dynamic Midi-Tower In 2 verschiedenen Größen h=60mm und h=93mm Lochabstand für Befestigung im Gehäuse 80mm x 80mm Bracket for the Corsair XD5 pump in the Lian Li PC-O11DX Dynamic…
I printed the parts from PETG with the following settings: - Line width: 0.45mm - Number of outer perimeters: 4-5 - Number of bottom layers: 5 - Number of top layers: 5 - Infill: 15% - 20% The assembly requires the following components: -…
you'll need two of the things - they are exactly mirrored. had to cut it based on the build volume of my genius. a little CA glue in between them, two screws to the bottom of the case, two screws to the middle fan. works like a charm :)
I made this to allow you to have in insert for the GoPro Hero11 inside the media mod, as well as having the light attached as well as a GoPro Max. SD Slot can be a bit tight and may need sanding. Printed in PLA 10% infill
When you install two 120mm fans on the side there will be a little gap where the air can go outside. The blocker on the bottom improves the airflow from the front fans and that the air can escape due to the negative pressure (10x intake…
I made this simple bracket to hold an Aquaero 6 Pro inside my O11Dynamic XL pc-case, right behind the front glass panel.
These guides exactly fit two Phanteks Neon light strips inside a Lian-Li O11 Dynamic case. The one guide is designed to be stuck to the back with double sided tape and guides a strip around the GPU and a 120mm rear fan. The other is…
Support GoPro11 for the GEPRC Vapor X5. Angle 20°
Remixed another model to make the GPS level with the top plate to avoid prop collision and added screw holes that fit the Tyro129 and Tyro119. DJI FPV unit is zip tied to the top of the quad with the antennas feeding into this print.…
Most mounts for the Hero11 Mini on the Siren F5 are 25 degrees, so I borrowed a couple files and smooshed them together to make this "masterpiece". Flight (and crash) tested, leaves plenty of space for the battery, balances well, and is…
Small, neat, without unnecessary fastenings. Printed, clicked!
I was a bit fed up of the OG stand for this smart screen an did this adapter to adapt it within my PC case that I just moved in my desk. Therefore, in addition to look at all of these LEDs, I can now monitor my PC health. It fits a 95°…
After Ive created a Remix of SirCBO Design for the Dynamic XL I was done with it and only used it for Cables.... Meanwhile Ive changed a lot in my System and I am Planning to lead my softubes to the backside of the Case and from there to…
Decided to print a bracket that can fit into my Lian Li O11 Dynamic case. Wanted to add 80mm fans to the back of the case to help with heat removal especially behind my vertical mounted graphics card where I hound a hot spot of air…
This is a part I designed to mount an official raspberry pi 7 inch touch screen in an O11 dynamic pc case. I used 4m hex screws and nuts to attach the mount the top 120 mm exhaust fan. It is pretty basic at this point but it is…
This is a bezel for cleaning up the look of adding a sensor 7" display panel from Amazon . The Youtube video that inspired this can be found at https://youtu.be/T6C50GYZfEI Use qty 4, 3mm x 6mm long cap head screws to mount the bezel to…
This is a LCD mount for the Jun-Electron 7inch touch display popular on Amazon. It sits where the Lian-Li Der Bauer badge is in the back. Link to the display: https://www.amazon.com/Raspberry-Portable-Monitor-inch-Screen/dp/B08BC6BXXD/
A small model that can be attached to the back bracket to hold two 80mm fans to provide some air flow on the drives in the back cage. I used the Noctua rubber pins to mount it to the bracket itself as the photo shows.
I loved this mount for the PC case, but I don't run a top fan on my PC, so I remixed it to move the mounting holes to the top of the print Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.15…
This is a simple dual SSD caddy you can use to put two 2,5" SSD drives into the 3,5" HDD bay which is used in the Lian Li O11D EVO RGB computer case. I used the step file for this PC case from the Lian Li website:…
It mounts to the Hexagonal Mesh at the Back. I fitted it to the removable hard drive bay cover, but im pretty sure it fits everywhere. It is designed to work with the included USB Type C cable. Assembly: Insert the cable from the bottom a…
Montując wentylatory na przodzie obudowy - zamiast szyby , można zamontować sobie obok kratki na filtr Montowane na magnes od dołu i góry , cały widoczny filtr składa się z 3 elementów , środkowy element nie ma gniazd na magnesy . Górny i…
support pour la GoPro11 pour la frame Nord5 de NordFPV. Angle:20°
recently replaced an aging Lian li O11 dynamic and the kit i had didn't fit in the new case. i found this amazing model by Pixelglance3d https://www.printables.com/model/77723-watercooled-gpu-vertical-bracket but when i went to print it,…
Stand for the DSO112A Oscilloscope. With the possibility to attach a strap to hang it. Check also my other designs: https://www.printables.com/social/201278-hans/models
Adapts the Lian-Li hot swap hard drive bay into the back of the O11D EVO RGB where the original hard drives mounted. Uses six of the mounting screws from the hot swap bay, and reuses the screws from the original hard drive mount on the…
The way my new PC build is going to sit on my desk, It would be at an angle and cables would be visible. I drew this up quick in Fusion360 to cover up and route the cables around the back and through the grommet. It's simply doublesided…
My cat loves sleeping on my PC, i am not too fond of my cat sleeping on my PC as she has coughed up som nasty stuff that has been expelled into my case.. not to speak about the kittylitter dust that has filled the inside of my case. No…
This template can be used to recreate the rubber feet on the Standard Apple ADB keyboard MO116. Best fit I found was 0.8mm rubber sheet with a thin double sided tape on one side to attach it to the keyboard after cleaning the old guu off.…
With this design, you can mount your EK Water Blocks Pump to the O11D. Prints without supports.
Selbsterlärent Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: No Supports: Yes Resolution: 0.16 Infill: 25% Filament: Polymaker Polyflex TPU Black Notes: 0.3 layer Category: Tool Holders & Boxes
The Problem The O11D's rear grill wasn't designed for fan mounting. Attaching fans directly to the metal is inconvenient, and the rear panel ends up blocking a significant portion of the airflow. This duct solves that by providing proper…
I created this coverplate to hide the annoying dead space between the bottom and side fans. I also made a YouTube Short about it:
Lian Li O11 Air Mini Feet for Under-Desk Tape Mount To save desk space, I decided to create my own under-desk mount. To support it better, I modified the feet to accommodate tape. I used M6 inserts. I designed it to use four inserts in…
A foot bracket for NZXT's GPU Riser to make the GPU level w/o touching the Lian Li O11 Vision Compact case's bottom mesh. The foot that the vertical riser comes with would push right down into the mesh tray at the bottom of the case. This…
🟩 🟦 🟦 🟪 🟥 🟧 🟨 This is a simple case mod for the Lian Li O11D. My specific one is the O11D Dynamic EVO RGB - I guess it fits others in the series but I am not sure - the top appears to have the same mounting points on the others in the…
Included is a base block for modifying to fit your needs The main block fits a microSD reader from the falcon2 pro H7.53mmW19.95mmL26.42mm with a small extension
Fills the bare floor around three 120 mm bottom fans in the Lian Li O11 Vision and sits flush with the top of 25 mm fans , for a clean, finished look through all that glass. No screws, glue or tools. Five pieces Front Tray : L-shaped.…
Fills the empty floor space around the bottom fans of the Lian Li O11D EVO XL. The front tray covers the floor between the front glass and the first fan, plus the space in front of the motherboard tray. A two-piece strip runs along the…
Fills the empty floor space around the bottom fans of the Lian Li O11D EVO XL. The front tray covers the floor between the front glass and the first fan, plus the space in front of the motherboard tray. A two-piece strip runs along the…
Seals the gap between the side fan bracket and the side panel on the Lian Li O11 Dynamic EVO RGB , so each side fan pulls air straight in through the panel instead of recirculating warm air from the back chamber. Made for the EVO RGB…
Raises the Lian Li O11 Dynamic EVO RGB exactly 2.0 in (50.8 mm) , for more room under the bottom fans and easier access to the bottom I/O. Built from Lian Li's CAD model The EVO RGB stands on four moulded feet with straight outer faces…
Fills the bare floor around three 120 mm bottom fans in the Lian Li O11 Dynamic EVO RGB and sits flush with the top of 25 mm fans , for a clean, finished look through the glass. No screws, glue or tools. Three pieces Front Tray :…
Fills the bare floor around three 140 mm bottom fans in the Lian Li O11 Dynamic EVO RGB and sits flush with the top of 25 mm fans , for a clean, finished look through the glass. No screws, glue or tools. Three pieces Front Tray :…
Seals the gap between the side fan bracket and the right side panel on the Lian Li O11 Vision , so each side fan pulls air straight in through the panel instead of recirculating warm air from the back chamber. Check first: the shroud only…
NB! The O11 Dynamic EVO is not supported as it is totally different from O11D EVO RGB. The print bed size for EVO RGB is minimum 326mm. Internal 14-inch diagonal LCD custom made for LianLi Dynamic O11 Dynamic EVO RGB/Mini PC case. For the…
I have remixed the Backplate from SirCBO for the O11 Dynamic XL as his version is too long for the XL. I uploaded the original Design and a modified version where all holes are closed and a Hole for an HDMI Cable was created. Have fun.…
NB! The O11 Dynamic EVO is not supported as it is totally different from O11D EVO RGB. The print bed size for EVO RGB is minimum 326mm. Internal 14-inch diagonal LCD custom made for LianLi Dynamic O11 Dynamic EVO RGB/Mini PC case. For the…
As I needed a way to route cables out of my Lian Li O11 Dynamic for a JBOD, I inspected the original one and made a model with a cutout for cables on the top left. I use the solid version as that was simple and the one I created first and…
Printed in PETG with 10% infill Thanks @ CromFr for your design that I could remix for my use
I've converted my Tyro129 to DJI FPV. For this reason, the 3rd plate (analog video transmitter) isn't used so i created a blank plate that I can zip tie my receiver and wire bundles onto. My DJI FPV transmitter will mount on top of the…
I made this model for Lian Li O11 Dynamic. For whatever reason, my cable grommets fell apart after a few years, so i needed to create replacement. Not sure if it fits any other model. This is a TPU print. I printed mine with: Sunlu 95a…
I have remixed the Backplate from SirCBO for the O11 Dynamic XL as his version is too long for the XL. I uploaded the original Design and a modified version where all holes are closed and a Hole for an HDMI Cable was created. Have fun.…
https://www.tiktok.com/@notoccamsrazor/video/7310117366765997342 The brand of LCD panel I used this with is the Geekpi on Amazon - https://www.amazon.com/dp/B0CHRD7CQ3?ref=ppx_yo2ov_dt_b_product_details&th=1 Secure the “LCD Panel Mounting…
Since these models may be used with electrical components, if you use these models, it is at your own risk. These models will not meet code requirements, so use your best judgement if they should be used in your application or not. If…
Created a clip to mount my GoPro Hero11 Mini to my backpack and weighted vest.
