1 / 10
Lian Li O11D EVO RGB Side Intake Fan Shroud – 120 / 140 mm — zdjęcie 1
1 / 10

Lian Li O11D EVO RGB Side Intake Fan Shroud – 120 / 140 mm

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A 40 mm duct that seals each side intake fan to the side panel, so the fans pull fresh air instead of warm case air.

Ocena
0 / 5
Polubienia
0
Pobrania
0
Wydruki
0
Wyświetlenia
4
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Computers
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Seals the gap between the side fan bracket and the side panel on the Lian Li O11 Dynamic EVO RGB, so each side fan pulls air straight in through the panel instead of recirculating warm air from the back chamber.

Made for the EVO RGB

Every file was checked against Lian Li's official O11D EVO RGB CAD model. The side fan bracket sits 40.6 mm from the inside of the side panel, so these shrouds are 40 mm deep. The EVO XL needs 45 mm and has its own listing.

Check first: the shroud only works if your side panel is vented in front of the side fans. Lian Li's CAD model shows that panel as plain steel. On a solid panel the fans would have no air to pull, so don't fit them.

Pick your file

Your fans

Hole spacing

File

Print

120 mm, any brand: Arctic P12 / P12 Pro, Noctua NF-A12x25 / NF-F12 and most others

105 mm

120mm Fan – all brands

3

140 mm Arctic P14 / P14 Pro

125 mm

140mm Arctic P14 & P14 Pro

2

140 mm Noctua NF-A14x25 G2 and most other brands

124.5 mm

140mm Noctua & most brands

2

Not sure? Your fan's spec sheet lists the hole spacing. The two 140 mm files differ by 0.35 mm at each screw, which is enough to bind.

140 mm versions have a front notch

With two 140 mm fans the shrouds reach the front of the bracket, where the side panel's folded edge sticks 4.7 mm into the gap. One wall is trimmed back 4.6 mm to clear it. Fit that side toward the front of the case.

What you'll need (not included)

  • M5 × 15 mm self-tapping fan screws, 4 per shroud: 12 for three 120s, 8 for two 140s. Stock 10 mm screws won't reach through the 3 mm screw seat.

  • A #2 Phillips with a 100 mm (4 in) or longer shaft. A magnetic tip helps.

Print settings

Setting

Value

Material

PETG

Orientation

Fan side down (round opening and 4 holes on the bed)

Supports

None

Layer height

0.2 mm

Walls

3

Infill

15 %

First layer

Elephant's-foot compensation on

Plastic

62 g (120 mm), 70 g (140 mm) per shroud

Install (10–15 minutes)

  1. Shut down, switch the PSU off and unplug the power cord.

  2. Take off the right side panel.

  3. Unscrew one fan's four screws from the bracket.

  4. Line up the shroud and drive four M5 × 15 mm screws down the corner channels.

  5. Repeat for each fan, refit the panel and plug back in.

Fit notes

  • The opening is at least as large as each listed fan's opening, so no blades are covered.

  • On fans with a smaller opening (Arctic P14, Noctua NF-A14x25 G2, NF-A12x25) a 1–3.5 mm strip of fan frame shows inside the shroud. That's expected.

  • Measured with the side fan bracket in its stock position.

Images are renders on Lian Li's CAD model. Not affiliated with Lian Li, Arctic or Noctua.

Tagi