Lian Li O11 Vision Side Intake Fan Shroud – 120 / 140 mm (Arctic, Noctua & more)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A 58 mm duct that seals each side intake fan to a vented side panel, so the fans pull fresh air, not warm case air.
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 1
- Wydruki
- 0
- Wyświetlenia
- 20
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Computers
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Seals the gap between the side fan bracket and the right side panel on the Lian Li O11 Vision, so each side fan pulls air straight in through the panel instead of recirculating warm air from the back chamber.
Check first: the shroud only works if your right side panel is vented or meshed in front of the side fans. Lian Li’s CAD model shows the O11 Vision’s panel as plain steel there. On a solid panel the fans would have no air to pull, so don’t fit them. Leave the side fans unshrouded instead.
Made for the O11 Vision
Every file was checked against Lian Li’s official O11 Vision CAD model. The Vision’s side fan bracket sits 58.7 mm from the inside of the side panel, deeper than any O11 Dynamic EVO, so these shrouds are 58 mm deep. The EVO XL (45 mm) and EVO RGB (40 mm) versions have their own listings.
Pick your file
Your fans | Hole spacing | File | |
|---|---|---|---|
120 mm, any brand: Arctic P12 / P12 Pro, Noctua NF-A12x25 / NF-F12 and most others | 105 mm | 120mm Fan – all brands | 3 |
140 mm Arctic P14 / P14 Pro | 125 mm | 140mm Arctic P14 & P14 Pro | 2 |
140 mm Noctua NF-A14x25 G2 and most other brands | 124.5 mm | 140mm Noctua & most brands | 2 |
Not sure? Your fan’s spec sheet lists the hole spacing. The two 140 mm files differ by 0.35 mm at each screw, which is enough to bind.
No notch needed
Nothing else in the case reaches into the gap between the bracket and the panel (the nearest part is 4.7 mm away), so every file fits either way round.
What you’ll need (not included)
M5 × 15 mm self-tapping fan screws, 4 per shroud: 12 for three 120s, 8 for two 140s. Stock 10 mm screws won’t reach through the 3 mm screw seat.
A #2 Phillips with a 100 mm (4 in) or longer shaft. The screw heads sit about 55 mm down the corner channels. A magnetic tip helps.
Print settings
Setting | Value |
|---|---|
Material | PETG |
Orientation | Fan side down (round opening and 4 holes on the bed) |
Supports | None |
Layer height | 0.2 mm |
Walls | 3 |
Infill | 15 % |
First layer | Elephant’s-foot compensation on |
Plastic | About 89 g (120 mm), 104 g (140 mm) per shroud |
Install (10–15 minutes)
Shut down, switch the PSU off and unplug the power cord.
Take off the right side panel.
Unscrew one fan’s four screws from the bracket.
Line up the shroud and drive four M5 × 15 mm screws down the corner channels.
Repeat for each fan, refit the panel and plug back in.
Fit notes
The opening is at least as large as each listed fan’s opening, so no blades are covered.
On fans with a smaller opening (Arctic P14, Noctua NF-A14x25 G2, NF-A12x25) a 1–3.5 mm strip of fan frame shows inside the shroud. That’s expected.
Measured with the side fan bracket where Lian Li’s model has it. The bracket is reversible; if yours is in the other position, measure the gap again.
Images are renders on Lian Li’s CAD model; the fans are simple stand-ins. Not affiliated with Lian Li, Arctic or Noctua.