Lian Li O11 Vision Bottom Fan Floor Tray – 3 × 120 mm Fans
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Drop-in floor cover for three 120 mm bottom fans. Fills the space around them and sits flush with the fan tops.
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 1
- Wydruki
- 0
- Wyświetlenia
- 7
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Computers
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Fills the bare floor around three 120 mm bottom fans in the Lian Li O11 Vision and sits flush with the top of 25 mm fans, for a clean, finished look through all that glass. No screws, glue or tools.
Five pieces
Front Tray: L-shaped. Covers the floor between the front glass and the first fan, plus the space in front of the motherboard tray up to the side fans.
Side Tray, FRONT piece: a slim strip along the side glass beside the fans. Its size matches your tray.
Side Tray, REAR piece: locks on with a small dovetail and runs to the rear. The same for everyone.
Motherboard Strip, FRONT + REAR: new for the Vision. Its fan bracket leaves 57 mm of bare floor along the motherboard tray; this covers it, with a slot over the floor’s cable hole. The same for every size.
Built from Lian Li’s CAD model
Every file was checked against the official O11 Vision model. Nothing touches the glass, trim, bottom fans, side fans or motherboard tray. Every support pad and rib lands on a flat spot, and every piece keeps at least 0.9 mm from everything around it. The pads also stay clear of the front foot screw, so it works with the bolted riser feet.
Pick your size
Measure from the inside face of the front glass straight back to the front edge of the first bottom fan’s frame (the hard frame, not a rubber corner).
Sizes (mm): 25, 27, 29, 31 · 42, 44, 46 · 57, 59 · 69, 71, 73 · 84, 86, 88, 90
Three butted 120 mm fans can only sit in certain places on the bracket’s slots, so the gap is about 25–32, 42–47, 57–59, 69–74 or 84–91 mm. Between two sizes? Use the smaller one.
Then print five files. For a 27 mm gap, for example:
Front Tray_120_gap27mm.stl (Front Tray folder)
Side Tray_120_FRONT_gap27mm.stl (Side Tray folder)
Side Tray_120_REAR.stl (Side Tray folder, the same for every size)
Motherboard Strip_120_FRONT.stl and Motherboard Strip_120_REAR.stl (Motherboard Strip folder, the same for every size)
Fans spaced apart, or a size that isn’t listed? Open the included .scad files in OpenSCAD (free), keep fan_size = 120, type in your exact measurement, side fan thickness (0 = no side fans) and bottom fan thickness, then export the STL.
What it assumes
Three 120 mm fans on the stock bottom bracket, sitting on its plate.
25 mm thick bottom fans. Use the .scad file for 28 mm fans.
Side intake fans up to 28 mm thick. The tray stops 1.5 mm short of them.
Print settings
Setting | Value |
|---|---|
Material | PETG or PLA (PETG if the PC sits somewhere warm) |
Orientation | As exported, top face down |
Supports | None |
Layer height | 0.2 mm |
Walls | 3 |
Infill | 15–20 % |
Size | Tray 208 × 178 mm, side strip pieces up to 222 × 10 mm, motherboard strip pieces 149 × 53 mm |
Bed | 220 × 220 mm or larger |
Plastic | About 190 g per set in PETG (tray 74–95 g depending on size) |
Install (about 5 minutes)
Shut down, switch the PSU off and unplug the power cord.
Take off the side glass (and the front glass if that’s easier).
Route the bottom fans’ cables first. Use the slots over the floor’s cable holes.
Lower the Front Tray into the front corner, in front of the fans.
Set both REAR pieces against the rear: the side strip along the glass, the motherboard strip along the motherboard.
Drop each FRONT piece in from above so its dovetail lands in its rear piece. If one is tight, sand the tab lightly.
Refit the glass and plug back in.
Images are renders on Lian Li’s CAD model; the fans are simple stand-ins, and some images show the 120 mm set. Not affiliated with Lian Li.