1 / 8
Lian Li O11D EVO RGB 2-Inch Riser Feet  Bolt-On, Set of 4 — zdjęcie 1
1 / 8

Lian Li O11D EVO RGB 2-Inch Riser Feet Bolt-On, Set of 4

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Lifts the case 2 in (50.8 mm) for more bottom-fan airflow. Each riser wraps a stock foot and bolts into its thread.

Ocena
0 / 5
Polubienia
0
Pobrania
0
Wydruki
0
Wyświetlenia
3
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Computers
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Raises the Lian Li O11 Dynamic EVO RGB exactly 2.0 in (50.8 mm), for more room under the bottom fans and easier access to the bottom I/O.

Built from Lian Li's CAD model

The EVO RGB stands on four moulded feet with straight outer faces and 20° sloped inner faces. Each riser follows that shape and was checked against every part of the official model.

How it attaches

  • A 10 mm socket wraps the stock foot with 0.6 mm clearance.

  • A 10.8 mm stem goes up into the hole in the middle of each foot, so nothing wobbles or twists.

  • Bolted (most secure): swap each foot's stock screw for a #6-32 × 1-1/4" that goes up through the riser and the foot into the case's own thread. The risers stay on when you lift the case.

  • No tools: or leave the stock screws in. The stems stop below them.

  • The front-right riser is open on one side so it clears the bottom I/O module.

Print order

  1. 1_PRINT-FIRST_Fit-Test_all-4-corners: about 125 g. Press each piece onto its foot first.

  2. 2_PREFERRED_All-4-Risers_one-plate: the full set, 182 × 163 mm, fits a 200 mm bed.

  3. Single risers: the same parts one at a time, for small beds or reprints.

What you'll need (bolted option, not included)

  • 4 × #6-32 × 1-1/4" pan-head machine screws (or M3.5 × 30–32 mm). Length matters: 1" won't reach the thread, and 1-1/2" can hit the steel above it.

  • A #2 Phillips with a slim shaft at least 50 mm long.

Print settings

Setting

Value

Material

PETG (ASA or ABS also good; PLA+ in a cool room)

Orientation

As exported, base down

Supports

None

Nozzle / layer

0.4 mm / 0.2 mm

Walls

4, with 5 top and 5 bottom layers

Infill

25 % gyroid

Plastic

About 500 g per set, fit test about 125 g

Install

  1. Shut down, switch the PSU off and unplug the power cord.

  2. With a helper steadying it, tip the case back so the front feet lift about 10 cm.

  3. Bolted: remove the stock screw from each front foot.

  4. Press the front risers on and screw them in from underneath. Don't overtighten; it threads into thin steel.

  5. Repeat at the rear.

STEP files and the Python source are included, so you can build other lifts, for example 2.5 in.

Images are renders on Lian Li's CAD model. Not affiliated with Lian Li.

Tagi