Lian Li O11D EVO RGB Bottom Fan Floor Tray – 3 × 120 mm Fans
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Drop-in floor cover for three 120 mm bottom fans. Fills the space around them and sits flush with the fan tops.
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 0
- Wydruki
- 0
- Wyświetlenia
- 8
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Computers
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Fills the bare floor around three 120 mm bottom fans in the Lian Li O11 Dynamic EVO RGB and sits flush with the top of 25 mm fans, for a clean, finished look through the glass. No screws, glue or tools.
Three pieces
Front Tray: L-shaped. Covers the floor between the front glass and the first fan, plus the space in front of the motherboard tray. Notched around the aluminium pillar in the glass corner.
Side Tray, FRONT piece: runs along the side glass beside the fans. Its size matches your tray.
Side Tray, REAR piece: locks on with a dovetail and runs to the rear panel. The same for everyone.
Built from Lian Li's CAD model
Every file was checked against the official O11D EVO RGB model. Nothing touches the glass, trim, pillar, bottom fans or side fans. Every support pad and rib lands on a flat spot, and the rim stays above the glass trim so the RGB-lit edge stays uncovered.
Pick your size
Measure from the inside face of the front glass straight back to the front edge of the first bottom fan's frame (the hard frame, not a rubber corner).
Sizes (mm): 31, 33, 35, 37, 39, 41 · 45 to 71 in 2 mm steps · 76, 78, 80, 82, 84, 86
Three butted 120 mm fans can only sit in certain places on the bracket's slots, so the gap is about 31–41.5, 45–72.5 or 76–87 mm. Between two sizes? Use the smaller one.
Then print three files. For a 39 mm gap, for example:
Front Tray_120_gap39mm.stl (Front Tray folder)
Side Tray_120_FRONT_gap39mm.stl (Side Tray folder)
Side Tray_120_REAR.stl (Side Tray folder, the same for every size)
Fans spaced apart, or a size that isn't listed? Open the included .scad files in OpenSCAD (free), keep fan_size = 120, type in your exact measurement, side fan thickness (0 = no side fans) and bottom fan thickness, then export the STL.
What it assumes
Three 120 mm fans on the stock bottom bracket, sitting on its plate.
25 mm thick bottom fans. Use the .scad file for 28 mm fans.
Side intake fans up to 28 mm thick. The tray stops 1.5 mm short of them.
The standard (non-reversed) case layout.
Print settings
Setting | Value |
|---|---|
Material | PETG or PLA (PETG if the PC sits somewhere warm) |
Orientation | As exported, top face down |
Supports | None |
Layer height | 0.2 mm |
Walls | 3 |
Infill | 15–20 % |
Size | Tray 212 × 180 mm, strip pieces up to 218 × 26 mm |
Bed | 220 × 220 mm or larger. Turn the strips diagonally if your skirt needs room. |
Plastic | About 95–130 g per set in PETG, depending on size |
Install (about 5 minutes)
Shut down, switch the PSU off and unplug the power cord.
Take off the side glass (and the front glass if that's easier).
Route the bottom fans' cables first.
Lower the Front Tray into the front corner, around the pillar.
Set the REAR strip piece along the side glass, against the rear panel.
Drop the FRONT strip piece in from above so its dovetail lands in the rear piece. If it's tight, sand the tab lightly.
Refit the glass and plug back in.
Images are renders on Lian Li's CAD model; some show both fan sizes. Not affiliated with Lian Li.