1 / 7
Print-in-place ring needle holder with a pin-and-holes lock — zdjęcie 1
1 / 7

Print-in-place ring needle holder with a pin-and-holes lock

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Mayo-Hegar style needle holder printed as a single part, no screw, no assembly. The pivot is a rivet printed in place an

Ocena
0 / 5
Polubienia
0
Pobrania
4
Wydruki
0
Wyświetlenia
26
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Medical Tools
Licencja
Creative Commons — Attribution

Prototype of a ring-handled needle holder, 154 mm long and 22 g in PLA, designed around a specific complaint: on a real Mayo-Hegar, locking the suturing position takes force and the instrument keeps slipping out of the ratchet. This model replaces the toothed ratchet with a positive-engagement lock and prints as one piece.

How it works

The two arms cross at a riveted pivot printed in place, with 0.5 mm radial clearance and 0.6 mm between the two halves. Next to the rings, a bar on one arm carries an oblong flat-topped pin and the bar on the other arm, which passes over it, carries four oblong holes. With the pin inside a straight-walled hole, neither squeezing nor pulling the handles moves it. It only comes out if the upper bar is lifted 1.7 mm.

Use

  • To release: twist the rings in opposite directions, one up and one down, the same gesture used to release a hemostat. The upper bar lifts and the pin leaves the hole.

  • To lock: squeeze to the position you want and let go. The bar drops and the pin enters the nearest hole with a click.

  • The four positions are 4 mm apart at the lock, which is about 1.5 mm at the jaw tips.

The part comes off the printer closed, with the pin already inside the first hole. The pivot turns as soon as it leaves the bed, without forcing. If the first layer has bonded across a clearance, twisting the rings once is enough to free it.

Geometry

  • Length 157 mm in the model (154 mm printed), 98 mm across the outside of the rings, 6 mm thick.

  • Stadium-shaped rings, 34 x 24 mm inside, 4 mm wall.

  • 25 mm jaws with a cross-hatched pyramid grip at 1.5 mm pitch, offset half a pitch between the two jaws.

  • Pivot with a 24 mm disc, 8 mm pin and a flush conical head.

  • Lock pin 2.2 x 4 mm with a fillet at the base. Holes with 0.4 mm clearance per side.

Limitations

This is a prototype to validate the mechanism, not an instrument. It cannot be sterilized, the jaw grip wears, and the handles hold a fraction of what steel would. A needle is held by the elasticity of the arms between two lock positions, not by a spring. PLA is too flexible for real use, but enough to show that the lock engages and releases as intended. [A physician tried the prototype and confirmed the lock and release gesture.]

Files

  • porta_agulhas_argolas.stl: the part in its print position, closed. Print it flat as it is, no supports.

Academic project for the Design and 3D Printing course, MSc in Computer Science and Multimedia Engineering, ISEL (Lisbon), 2026/2027.

Print instructions

Printed on a Creality Ender-3 V3 KE, 0.4 mm nozzle, PLA, no supports, 1 h 30 min. The clearances are 0.5 and 0.6 mm, so the settings that matter are the ones that keep the gaps open and the short bridges supported.

  • Layer height 0.2 mm, initial layer 0.2 mm

  • Line width 0.4 mm

  • 4 walls, 5 top and 5 bottom layers, 100 % infill

  • Initial layer horizontal expansion -0.15 mm (compensates elephant’s foot, which would close the gap between the jaws)

  • Hole horizontal expansion +0.1 mm

  • Print thin walls on, minimum wall line width 0.3 mm, minimum feature size 0.1 mm

  • Temperature 210 C, initial layer 215 C, bed 60 C

  • Speed 90 mm/s, outer wall 40, inner wall 60, initial layer 30

  • Retraction 0.8 mm at 40 mm/s, Z hop 0.3 mm, combing not in skin

  • Minimum layer time 10 s, fan 100 % from layer 3

  • Bridge settings enabled

  • Supports off

  • Adhesion: skirt, 3 lines, 5 mm (a brim gets into the pivot and jaw clearances)

  • Z seam at the sharpest corner

For PETG, open the clearances by 0.1 to 0.2 mm, since it tends to bond more across the short bridges.

Tagi