1 / 3
Mennekes 10833 Schuko Kupplung Deckel-Halteband — zdjęcie 1
1 / 3

Mennekes 10833 Schuko Kupplung Deckel-Halteband

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Ersatzteil für das originale Halteband der Mennekes 10833 Schuko Kupplung

Ocena
0 / 5
Polubienia
0
Pobrania
1
Wydruki
0
Wyświetlenia
9
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Deutsch

Mennekes 10833 – Ersatz-Halteband (Kupplung)

Da das originale Halteband der Mennekes 10833 Kupplung leider nicht einzeln als Ersatzteil erhältlich ist und ein abgerissener Deckel schnell zu verschmutzten Kontakten führt, habe ich dieses Ersatzteil selbst designed.

  • Eigenschaften: Passgenau für die Mennekes 10833 Kupplung, schützt vor dem Verlust des Deckels und hält die Kontakte sauber.

  • Druckempfehlung: Gedruckt in TPU (Flex-Filament) für die perfekte Mischung aus Flexibilität und Haltbarkeit. Bisherige Praxistests im Alltag verlaufen sehr erfolgreich!

Montage & Hinweise

  1. Alte Bandreste entfernen: Zuerst müssen die Reste des alten, gerissenen Haltebands aus dem Deckel entfernt werden. Am besten gelingt dies, indem man die Reste Stück für Stück mit einem starren Draht herausschiebt.

  2. Neues Halteband einsetzen: Das gedruckte TPU-Ersatzteil anschließend vorsichtig in den Deckel bzw. die Halterung reinschieben, bis es an Ort und Stelle sitzt.

  3. Wichtiger Sicherheitshinweis / Disclaimer: Arbeiten an elektrischen Anlagen und Betriebsmitteln dürfen gemäß DGUV Vorschrift 3 (und DIN VDE 0105-100) grundsätzlich nur von qualifiziertem Elektrofachpersonal (bzw. unter Leitung und Aufsicht einer Elektrofachkraft) durchgeführt werden. Der Anwender handelt eigenverantwortlich.

Viel Spaß beim Nachdrucken! Über ein Feedback oder ein geteiltes Foto eurer Prints freue ich mich.

 

-----------------------------

Englisch

Mennekes 10833 – Replacement Lid Strap (Coupling)

Since the original retaining strap for the Mennekes 10833 connector isn't available as a standalone spare part—and a lost lid quickly leads to dirty contacts—I designed this replacement strap myself.

  • Features: Custom-fit for the Mennekes 10833 coupling, prevents losing the protective cap, and keeps your contacts clean.

  • Print Settings: Recommended to print in TPU for the ideal balance of flexibility and durability. Real-world testing has been very successful so far!

Assembly & Instructions

  1. Remove old strap remnants: First, any remnants of the old, broken strap must be removed from the lid. This is best done by pushing them out piece by piece using a stiff wire.

  2. Install the new strap: Slide the printed TPU replacement part into position until it is securely seated.

  3. Important Safety Disclaimer: According to safety regulations, work on electrical systems and equipment must be carried out exclusively by qualified electricians or under their direction and supervision. Users assume all responsibility and liability for installation and use.

Happy printing! Feel free to leave feedback or post a photo of your makes.

Tagi