Liczymy pasujące modele…
UPDATE Now avaliable for BMW and Jetty Typ2 Plugs My Simple Design for a Bracket to mount on a Mennekes Typ 2 Charging Cable. This allows you to organize the cable while charging an avoid it to sit on the curb in the wet and muddy…
Simple wall mounted holder for cable spool and Mennekes Type 2 plug (car side). Model has optional covers for mount holes and also locking clip for cable - so it doesnt slip. Locking clip is "click on" the shaft in the holder. Print as…
Wall mount holder for EV cable with Mennekes Type 2 plug Easy to insert and remove plug from holder 150 mm width, 106 mm height and 103 mm depth Simple functional latch without spring or moving parts Recommended PETG, 3 walls, 20% infill
Connector holder (Mennekes type 2) for charging from a wallbox, including a hook for storing the coiled cable. Including a flexible locking. Printed from 150g PETG material. Mounted with two screws 5x25mm
I needed a neat looking plug holder, without the common “cable shelf” on top since my cable doesn't have any slack. Couldn't find any to my liking so I designed this. There's a little “nub” inside catching the hole in the plug so it…
New version of my holder for EV charger cable Type 2 (Mennekes). It has tilted slot for charging gun, so it fits more cramped places. Slot has drain hole - so the moisture buildup can flow away. Its mounted by scews with countersunk head…
This is a remix. Because, don't needing the parasol above the plugholder, I designed a little housing. As spring for the lever, I used one from a ballpen. For easier placement and fixation of the spring, I added a corresponding hole in…
Simple holder for electric vehicle (EV) charger with Type 2 (Mennekes) connector. Connector is slightly tilted, holds in place safely. Prusa spool is used for holding the cable, which can be pretty heavy, depending on length. I suggest…
Supports the weight of the charger, easy to take in/out.
So maybe you thought about getting a Type 2 to Schuko adapter on AliExpress for less than 30€ to charge your E-Bike at public charging stations that don't offer a Schuko port but a Type 2 Mennekes. Sth like:…
Designed to be printed vertically with minimal supports. Works on both PLA and PETG. Locking pin is kinda loose on mine so I put a little bit of foam tape on the inside of the case to bring up the slop. Note: You may have to draw the…
Most Type 2 holders on the internet are traced from a photo or a caliper. This one is built from the dimensioned drawings in IEC 62196-2:2022, standard sheets 2-IIe and 2-IIf - and then corrected twice by actually printing it and hanging…
Deutsch Mennekes 17038 – Ersatz-Halteband (Aggregat-Steckdose) Da das originale Halteband der Mennekes 17038 (in meinem Fall verbaut in einem Notstrom Aggregat) nicht als einzelnes Ersatzteil erhältlich ist und ein verlorener Deckel zu…
Deutsch Mennekes 10828 – Ersatz-Halteband Da das original Halteband des Mennekes 10828 Steckers leider nicht einzeln als Ersatzteil erhältlich ist und ein abgerissener Deckel schnell zu verschmutzten Kontakten führt, habe ich dieses…
Deutsch Mennekes 10833 – Ersatz-Halteband (Kupplung) Da das originale Halteband der Mennekes 10833 Kupplung leider nicht einzeln als Ersatzteil erhältlich ist und ein abgerissener Deckel schnell zu verschmutzten Kontakten führt, habe ich…
Deutsch Mennekes 17021 – Ersatz-Halteband Da das originale Halteband der Mennekes 17021 Steckvorrichtung nicht einzeln als Ersatzteil erhältlich ist und ein verlorener Deckel zu verschmutzten Kontakten führt, habe ich dieses passende…
New version of my holder for EV charger cable Type 2 (Mennekes). It has tilted slot for charging gun, so it fits more cramped places. Slot has drain hole - so the moisture buildup can flow away. Its mounted by scews with countersunk head…
Simple holder for electric vehicle (EV) charger with Type 2 (Mennekes) connector. Connector is slightly tilted, holds in place safely. Prusa spool is used for holding the cable, which can be pretty heavy, depending on length. I suggest…
A holder for the Mennekes type chargers for EV's. The holder will prevent strain on the cord and pins in the outlet.
Holder for my Car charger volvo v60 D6 hybrid. will fit all mennekes charger of the same model. Print Settings Printer: Anet a8 BLV Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 15 Filament: Any PLA any Category: Automotive
