1 / 7
Tool-Free Single-Clip Utensil Hook for Rotated IKEA SKÅDIS — zdjęcie 1
1 / 7

Tool-Free Single-Clip Utensil Hook for Rotated IKEA SKÅDIS

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Tool-free hook for a horizontal-slot SKÅDIS board; fit-tested only with the two pictured spatulas.

Ocena
0 / 5
Polubienia
1
Pobrania
1
Wydruki
0
Wyświetlenia
10
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Kitchen
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

A tool-free single-clip hook for utensils with a hanging hole, such as kitchen spatulas, for a 5 mm IKEA SKÅDIS pegboard mounted 90° from its normal orientation, so the slots run horizontally. Please check before you print:

- The clip only fits a SKÅDIS board with HORIZONTAL slots. On a board in the normal orientation (vertical slots) it does not fit.

- The arm is 8 × 8 mm and reaches 37.5 mm in front of the board. A lip at its front end points 10 mm down, so the front end is 8 mm wide and 18 mm tall in total. The hanging hole of your utensil has to fit over the arm and pass this front end; measure the hole before printing.

- We tested it with two kitchen spatulas that have an elongated hanging hole. Other utensils, heavier tools and other hole shapes were not tested.

What is included

- Hook (print as many as you need): one clip with two tabs and one latch, an arm with a front lip, and a sloped gusset under the arm, designed to print without supports.

- The 3MF project contains three hooks on one plate.

Tool-free clip (no screws)

- Put both tabs into the left ends of two neighbouring slots of one row (40 mm apart).

- Press the hook flat against the board and slide it about 7 mm to the right until the latch clicks into the slot below.

- Hang the utensil by its hanging hole over the arm, behind the lip.

- To take it off: remove the utensil first, pull the bottom edge a few degrees (about 3°) away from the board until the latch leaves the lower slot, keep it tilted, slide it to the left and pull it out.

- The clip is made for the 5 mm SKÅDIS board.

Printing

- Settings: Bambu Lab X1 Carbon, 0.4 mm nozzle, 0.20 mm layer height, Bambu PLA Matte (white), Textured PEI plate, 5 walls, 40 % gyroid infill, 8 mm outer brim, no supports.

- The hook prints upside down, with the top of the arm on the plate; the STL file is already oriented that way. Trim the brim cleanly.

- Our three hooks were printed with these settings on a larger plate together with other parts. The published 3MF with three hooks was slice-checked separately: slicer estimate approximately 52 min and 33.6 g of filament. That exact plate was not printed on its own.

- Only the X1 Carbon print was tested. Bambu Studio lists other printers for this profile internally; those were not tested.

Use and safety

- Indoor kitchen organizer. Fit-tested on one 5 mm SKÅDIS board with two kitchen spatulas, as in the photos. Only this fit was checked; no rated-load, overload, heat or long-term test was done.

- PLA softens at relatively low temperatures. Keep the hooks away from direct heat, steam and hot utensils. PETG and ASA were not tested with this design.

- Check the print and the mounting before every use. Do not use for sharp, heavy or breakable items, and do not mount where a falling utensil could hit someone.

Files

- Skadis_Single_Clip_Hook.stl (one hook)

- Skadis_Single_Clip_Hook_X1C_PLA.3mf (3MF project, three hooks with the print settings)

- Skadis_Single_Clip_Hook_Drawing.pdf (key dimensions)

There is no STEP file: the part was modelled as a mesh, so a STEP file would only contain the same triangles.

About the pictures: the photos show two printed hooks in use with two kitchen spatulas. The animation and the renders are made from the model file; the spatulas are simplified and the printed parts are shown in orange.

IKEA and SKÅDIS are trademarks of Inter IKEA Systems B.V. Bambu Lab, X1 Carbon, Bambu PLA and Bambu Studio are product names and/or trademarks of their respective owners. The names are used only to identify tested compatibility and the printer, material and software used for the prototype. This independent design is not affiliated with, sponsored or endorsed by any of these companies.

License: CC BY-NC-SA 4.0 (https://creativecommons.org/licenses/by-nc-sa/4.0/). Free to print, share and remix for non-commercial use, with attribution. Mark your changes and share remixes under the same license.

Deutsch (Kurzfassung)

Werkzeugloser Haken mit einem Clip für Küchenhelfer mit Aufhängeloch, etwa Pfannenwender, an einer IKEA-SKÅDIS-Lochplatte (5 mm), die um 90 Grad gedreht hängt, sodass die Langlöcher waagrecht laufen. An einer normal montierten SKÅDIS (Langlöcher senkrecht) passt der Clip nicht.

Der Arm ist 8 × 8 mm groß und reicht 37,5 mm vor das Brett; vorne zeigt eine Lippe 10 mm nach unten, das vordere Ende ist damit 8 mm breit und insgesamt 18 mm hoch. Das Aufhängeloch muss über den Arm passen und an diesem vorderen Ende vorbei; das Loch vor dem Druck messen. Getestet nur mit zwei Pfannenwendern mit länglichem Aufhängeloch.

Clip ohne Schrauben: beide Laschen ins linke Ende von zwei benachbarten Langlöchern einer Reihe (40 mm Abstand), flach ans Brett drücken und rund 7 mm nach rechts schieben, bis die Rastnase einrastet. Zum Abnehmen den Küchenhelfer abnehmen, die Unterkante etwa 3° vom Brett wegkippen, bis die Rastnase das untere Langloch verlässt, gekippt halten, nach links schieben und abnehmen.

Einstellungen: Bambu Lab X1 Carbon, mattes weißes PLA, 5 Wände, 40 % Gyroid, 8 mm breiter Rand (Brim), ohne Stützen, kopfüber (die STL-Datei ist schon so gedreht). Gedruckt wurden unsere drei Haken mit diesen Einstellungen auf einer größeren Platte zusammen mit anderen Teilen; das veröffentlichte 3MF mit drei Haken ergibt laut Slicer etwa 52 min und 33,6 g. Diese genaue Platte wurde nicht separat gedruckt. Andere Drucker sind nicht getestet.

Für die Küche im Innenraum; geprüft wurde nur die Passung mit zwei Pfannenwendern, eine Prüfung auf Nennlast oder Überlast sowie Wärme- und Langzeittests gab es nicht. PLA wird schon bei mäßiger Wärme weich: die Haken von direkter Hitze, Dampf und heißen Küchenhelfern fernhalten. Druck und Montage vor jedem Gebrauch prüfen. Nicht für scharfe, schwere oder zerbrechliche Gegenstände verwenden und nicht dort anbringen, wo ein herabfallender Küchenhelfer jemanden treffen könnte.

Lizenz CC BY-NC-SA 4.0 (https://creativecommons.org/licenses/by-nc-sa/4.0/).

Tagi