1 / 1
Upside-Down Sauce Bottle Holder (Parametric) — zdjęcie 1

Upside-Down Sauce Bottle Holder (Parametric)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Keeps More Nutrition sauce bottles, ketchup and other upside-down bottles in your fridge door.

Ocena
0 / 5
Polubienia
3
Pobrania
3
Wydruki
1
Wyświetlenia
40
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Kitchen
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Upside-Down Sauce Bottle Holder

A holder for "More Nutrition" sauce bottles. It works just as well for ketchup and anything else you usually store upside down.

I designed it specifically for a fridge door, but you can use it anywhere else too.

Ready-made downloads

These models can be downloaded directly and use the default settings (36 mm holes, 75 mm depth, 25 mm total height):

  • 2 holes: 90 mm long

  • 4 holes: 178 mm long

  • 6 holes: 266 mm long

  • 8 holes: 354 mm long

Printing

  • Print it upside down. The files are exported in their upright position, so flip them 180° in your slicer.

  • If your print bed is too small, split the model in your slicer using vertical dovetails.

Customize it in FreeCAD

The included FreeCAD file is fully parametric. Open the Parameter spreadsheet, change the values and recompute.

Holes and size

  • Hole_Count: number of holes

  • Hole_Diameter: diameter of the holes

  • Hole_Spacing: distance between hole edges

  • Edge_Distance: distance from block end to outer hole edge

  • Depth: depth of the block

  • Height: height of the block without feet

Rear notches (optional)

  • Notch_Left, Notch_Right: 1 = on, 0 = off, set individually

  • Notch_Width: width along the length

  • Notch_Depth: depth from the rear side

Rounding

  • Fillet: radius of all remaining edges

  • Fillet_Front: radius of the front vertical corners

Feet

  • Feet: 1 = on, 0 = off

  • Foot_Height, Foot_Width, Foot_Depth: size of one foot

Calculated automatically

  • Length, Pitch: total length and centre-to-centre distance of the holes

  • Foot_Pairs_L, Foot_Pairs_R: number of double feet, based on the hole count

  • Foot_Edge_Distance: distance of the feet from the edge

Note: Foot_Depth must be more than twice the Fillet radius. Otherwise the rounding fails or the model breaks, sometimes without an error message.


Halterung für Saucenflaschen auf dem Kopf

Eine Halterung für "More Nutrition" Saucenflaschen. Sie eignet sich genauso für Ketchup und alles andere, was man üblicherweise auf dem Kopf lagert.

Ich habe das Modell speziell für eine Kühlschranktür entwickelt, es lässt sich aber auch anders verwenden.

Fertige Downloads

Diese Modelle stehen direkt zum Download bereit und nutzen die Standardwerte (Löcher 36 mm, Tiefe 75 mm, Gesamthöhe 25 mm):

  • 2 Löcher: 90 mm lang

  • 4 Löcher: 178 mm lang

  • 6 Löcher: 266 mm lang

  • 8 Löcher: 354 mm lang

Drucken

  • Am besten auf dem Kopf drucken. Die Dateien sind aufrecht exportiert, also im Slicer um 180° drehen.

  • Ist das Druckbett zu klein, das Modell im Slicer mit vertikalen Dovetails teilen.

In FreeCAD anpassen

Die mitgelieferte FreeCAD-Datei ist frei parametrierbar. Tabelle Parameter öffnen, Werte ändern und neu berechnen.

Löcher und Grösse

  • Hole_Count: Anzahl Löcher

  • Hole_Diameter: Durchmesser der Löcher

  • Hole_Spacing: Abstand zwischen den Lochrändern

  • Edge_Distance: Abstand vom Blockende zum äusseren Lochrand

  • Depth: Tiefe des Blocks

  • Height: Höhe des Blocks ohne Füsse

Einschnitte hinten (optional)

  • Notch_Left, Notch_Right: 1 = ein, 0 = aus, einzeln schaltbar

  • Notch_Width: Breite entlang der Länge

  • Notch_Depth: Tiefe ab der Hinterseite

Verrundung

  • Fillet: Radius aller übrigen Kanten

  • Fillet_Front: Radius der vorderen vertikalen Ecken

Füsse

  • Feet: 1 = ein, 0 = aus

  • Foot_Height, Foot_Width, Foot_Depth: Masse eines Fusses

Automatisch berechnet

  • Length, Pitch: Gesamtlänge und Mittenabstand der Löcher

  • Foot_Pairs_L, Foot_Pairs_R: Anzahl Doppelfüsse, abhängig von der Lochzahl

  • Foot_Edge_Distance: Abstand der Füsse zum Rand

Hinweis: Foot_Depth muss mehr als doppelt so gross sein wie der Radius von Fillet. Sonst schlägt die Verrundung fehl oder das Modell geht kaputt, teils ohne Fehlermeldung.

Tagi