Upside-Down Sauce Bottle Holder (Parametric)
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Keeps More Nutrition sauce bottles, ketchup and other upside-down bottles in your fridge door.
- Rating
- 0 / 5
- Likes
- 3
- Downloads
- 3
- Makes
- 1
- Views
- 40
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Kitchen
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
Upside-Down Sauce Bottle Holder
A holder for "More Nutrition" sauce bottles. It works just as well for ketchup and anything else you usually store upside down.
I designed it specifically for a fridge door, but you can use it anywhere else too.
Ready-made downloads
These models can be downloaded directly and use the default settings (36 mm holes, 75 mm depth, 25 mm total height):
2 holes: 90 mm long
4 holes: 178 mm long
6 holes: 266 mm long
8 holes: 354 mm long
Printing
Print it upside down. The files are exported in their upright position, so flip them 180° in your slicer.
If your print bed is too small, split the model in your slicer using vertical dovetails.
Customize it in FreeCAD
The included FreeCAD file is fully parametric. Open the Parameter spreadsheet, change the values and recompute.
Holes and size
Hole_Count: number of holes
Hole_Diameter: diameter of the holes
Hole_Spacing: distance between hole edges
Edge_Distance: distance from block end to outer hole edge
Depth: depth of the block
Height: height of the block without feet
Rear notches (optional)
Notch_Left, Notch_Right: 1 = on, 0 = off, set individually
Notch_Width: width along the length
Notch_Depth: depth from the rear side
Rounding
Fillet: radius of all remaining edges
Fillet_Front: radius of the front vertical corners
Feet
Feet: 1 = on, 0 = off
Foot_Height, Foot_Width, Foot_Depth: size of one foot
Calculated automatically
Length, Pitch: total length and centre-to-centre distance of the holes
Foot_Pairs_L, Foot_Pairs_R: number of double feet, based on the hole count
Foot_Edge_Distance: distance of the feet from the edge
Note: Foot_Depth must be more than twice the Fillet radius. Otherwise the rounding fails or the model breaks, sometimes without an error message.
Halterung für Saucenflaschen auf dem Kopf
Eine Halterung für "More Nutrition" Saucenflaschen. Sie eignet sich genauso für Ketchup und alles andere, was man üblicherweise auf dem Kopf lagert.
Ich habe das Modell speziell für eine Kühlschranktür entwickelt, es lässt sich aber auch anders verwenden.
Fertige Downloads
Diese Modelle stehen direkt zum Download bereit und nutzen die Standardwerte (Löcher 36 mm, Tiefe 75 mm, Gesamthöhe 25 mm):
2 Löcher: 90 mm lang
4 Löcher: 178 mm lang
6 Löcher: 266 mm lang
8 Löcher: 354 mm lang
Am besten auf dem Kopf drucken. Die Dateien sind aufrecht exportiert, also im Slicer um 180° drehen.
Ist das Druckbett zu klein, das Modell im Slicer mit vertikalen Dovetails teilen.
In FreeCAD anpassen
Die mitgelieferte FreeCAD-Datei ist frei parametrierbar. Tabelle Parameter öffnen, Werte ändern und neu berechnen.
Löcher und Grösse
Hole_Count: Anzahl Löcher
Hole_Diameter: Durchmesser der Löcher
Hole_Spacing: Abstand zwischen den Lochrändern
Edge_Distance: Abstand vom Blockende zum äusseren Lochrand
Depth: Tiefe des Blocks
Height: Höhe des Blocks ohne Füsse
Einschnitte hinten (optional)
Notch_Left, Notch_Right: 1 = ein, 0 = aus, einzeln schaltbar
Notch_Width: Breite entlang der Länge
Notch_Depth: Tiefe ab der Hinterseite
Verrundung
Fillet: Radius aller übrigen Kanten
Fillet_Front: Radius der vorderen vertikalen Ecken
Füsse
Feet: 1 = ein, 0 = aus
Foot_Height, Foot_Width, Foot_Depth: Masse eines Fusses
Automatisch berechnet
Length, Pitch: Gesamtlänge und Mittenabstand der Löcher
Foot_Pairs_L, Foot_Pairs_R: Anzahl Doppelfüsse, abhängig von der Lochzahl
Foot_Edge_Distance: Abstand der Füsse zum Rand
Hinweis: Foot_Depth muss mehr als doppelt so gross sein wie der Radius von Fillet. Sonst schlägt die Verrundung fehl oder das Modell geht kaputt, teils ohne Fehlermeldung.