W1SFR Fat Boy Paddle Carry Case with Cable Bay and Magnetic Lid
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Two-piece carry case for the W1SFR Fat Boy paddle with a deep cable bay and magnet closure. No supports needed.
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 1
- Wydruki
- 0
- Wyświetlenia
- 15
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Electronics
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Overview
A two-piece protective carry case for the W1SFR Fat Boy torsion bar paddle. The paddle's rubber feet drop into sockets in the base floor, and the lid closes over it with shaped channels that straddle the fingerpiece and the torsion mount, so the paddle cannot shift or lift in transit. A cable bay behind the paddle holds the coiled cord, and four pairs of 8 x 2 mm magnets hold the lid on.
On the Air
The Fat Boy is a heavy stainless and brass paddle, and loose in a go-bag it can bend the lever or knock the contacts out of adjustment. This case keeps it locked in place and carries the cable with it, so it comes out of the pack ready to plug in. The parting line is stepped: it drops low at the front, so you can leave the paddle in the base and send from it at a picnic table, and rises at the rear so the cable bay is 41 mm deep. The cord runs straight back through a notch into the bay when you close the lid. Closed, the case is 84.2 x 171.2 x 59.2 mm.
Print Settings
- Printer: Bambu Lab X1C/X2D, 0.4 mm nozzle
- Material: PETG for both parts. PCTG, ASA, etc. is also fine. Not PLA.
- Layer height: 0.20 mm
- Wall loops: 5, so the cradle walls print nearly solid
- Infill: 15%
- Supports: none required
- Orientation: base floor down, lid upside down (top on the plate), as laid out in the 3MF. Every overhang is 45 degrees or steeper.
- Print time and filament use: not specified (solid-equivalent volume about 102 cm3 for the base and 116 cm3 for the lid)
Both parts fit together on one 256 mm plate.
Hardware and Assembly
- 8x 8 x 2 mm neodymium disc magnets
- CA glue or epoxy
1. Check your magnets with calipers before gluing. The pockets are 8.2 mm diameter x 2.2 mm deep, so magnets much thinner than 2 mm will sit recessed and hold weakly. Some "8 x 2" listings ship 1/16 in (1.6 mm) thick discs.
2. Glue four magnets into the base pockets: two at the front corners, two at the rear corners.
3. Before gluing each lid magnet, set it on its partner in the base and mark the face that touches, so every pair attracts.
4. Glue the lid magnets in with the marked face down into the pocket... no, with the marked face toward the base, and let the glue cure before closing the case.
5. Set the paddle in the base with its feet in the sockets, run the cord back through the notch, coil it in the bay, and close the lid. It only fits one way round.
Design Notes
- Pocket: 78.2 x 78.2 mm, sized for W1SFR's nominal 3 x 3 in (76.2 mm) base with 1 mm clearance. A measured base of 75.04 x 73.72 mm also fits.
- Feet sockets: 16 mm diameter x 1.5 mm deep. They're centered between the nominal and measured foot patterns, so either base size seats.
- Stepped split: 10 mm at the fingerpiece zone, the plate top (21.5 mm) through the middle, and 45 mm at the cable bay. The steps key the lid front to back, and a 1.5 x 4 mm tongue runs along the side walls through every step.
- Lid cradles: walls taper from 3.2 mm at the tip to 5.2 mm at the root, with filleted roots and gussets fused to the wall face. The fingerpiece walls tie into the lid's front wall and the mount walls tie into the lid divider, so neither stands free.
- Headroom: the lid ceiling sits 2 mm above the fingerpiece and 3.1 mm above the torsion mount. Side rims ride 0.5 mm above the plate top, so the plate can't lift.
- Finger scoops in both side walls expose the plate edge for lifting the paddle out. Pry notches front and rear help open the lid against the magnets.
- Every edge is chamfered or filleted with print orientation in mind.
The dimensioned drawing (PDF) shows the design intent. Where it differs from the model, the model dimensions are correct. The OpenSCAD source is parametric: paddle dimensions, clearances, split heights and magnet size are all at the top of the file.
Makes, remixes and fit reports from other Fat Boy owners are welcome.