Runde 7-Tage-Pillenbox / Round 7-day pill box (Ø 60 mm)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Pillbox 7 Days – kompakte Dose mit Kugelrastung / compact pill box with ball detent
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 0
- Wydruki
- 0
- Wyświetlenia
- 17
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Home Medical Tools
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Eine kleine, robuste Pillenbox für eine Woche.
- 7 Fächer plus eine geschlossene Stellung, 8 Rastpositionen im Abstand von 45°
- Wochentage (Mo bis So) außen am Rand, bündig eingelegt, damit der Multicolor-Druck sauber wird
- Der Pfeil auf dem Deckel zeigt die Drehrichtung
- Griffrillen am Deckelrand
- Maße: Ø 60 mm, Unterteil 13 mm hoch
Wichtig:
- Federn und Kugeln sind nicht im Lieferumfang. Du brauchst eine Druckfeder (Kugelschreiber) (Ø ca. 4,3 mm, auf etwa 6 mm kürzen) und eine Kugel mit 4 mm (Stahl oder selbst gedruckt).
- Zum Einbau liegt der Kugelschieber bei. Er drückt Feder und Kugel in das Federloch.
- Der Text lässt sich im Slicer ändern.
(English)
A small, sturdy pill box for one week.
- 7 compartments plus one closed position, 8 detent positions at 45° steps
- Weekdays (Mon–Sun) on the outer wall, inlaid flush for clean multicolour printing
- An arrow on the lid shows the turning direction
- Knurled lid edge
- Size: Ø 60 mm, base 13 mm high
Important:
- Springs and balls are not included. You need a compression spring (ballpoint pen)(Ø about 4.3 mm, cut to about 6 mm) and a 4 mm ball (steel or printed).
- The ball pusher is included for assembly. It pushes spring and ball into the spring hole.
- You can change the text in your slicer.
Anleitung (Deutsch)
1. Alle Teile drucken (siehe Druckeinstellungen).
2. Feder auf ca. 6 mm kürzen.
3. Erst die Feder, dann die Kugel in das Federloch im Deckelzapfen stecken.
4. Den Deckel nur ganz leicht auf das Unterteil setzen, noch nicht ganz herunterdrücken.
5. An der Deckelöffnung mit dem Kugelschieber Kugel und Feder in das Federloch drücken.
6. Kugelschieber entfernen und den Deckel ganz auf das Unterteil drücken. Beim Drehen rastet die Kugel in die Mulden ein.
Assembly (English)
1. Print all parts (see print settings).
2. Cut the spring to about 6 mm.
3. Put the spring in first, then the ball, into the spring hole of the lid pin.
4. Place the lid only loosely on the base, without pressing it down.
5. At the opening in the lid, use the ball pusher to push ball and spring into the spring hole.
6. Remove the ball pusher and press the lid fully onto the base. The ball clicks into the dimples as you turn it.
- Kugelschieber: flach auf eine Seitenfläche legen, der Kopf zeigt im 45°-Winkel nach oben. / Lay it flat on one of its side faces with the head pointing up at 45°.
- Farben / Colours: Pfeil, gelbe Tablette, rote Kapsel, Ringe und Texte sind eigene Körper, im Slicer jeweils eine Farbe zuweisen. / Arrow, yellow tablet, red capsule, rings and text are separate bodies, assign each a colour in the slicer.
Stückliste / Bill of materials
- 1× Unterteil / base
- 1× Deckel / lid (mit Einlagen / with inlays)
- 1× Kugelschieber / ball pusher
- 1× Druckfeder (z. B. aus einem Kugelschreiber), Ø ca. 4,3 mm, auf ca. 6 mm gekürzt / compression spring (e.g. from a ballpoint pen), Ø about 4.3 mm, cut to about 6 mm
- 1× Kugel 4 mm / 4 mm ball