1 / 16
Nvidia Tesla P40 / P100 / M40 40mm Fan Shroud: Single, 2, 3 and 4 Card (Parametric) — zdjęcie 1
1 / 16

Nvidia Tesla P40 / P100 / M40 40mm Fan Shroud: Single, 2, 3 and 4 Card (Parametric)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

40mm fan shroud for passive Tesla P40, P100 and M40 cards. Single plus ganged 2, 3 and 4 card versions. OpenSCAD source.

Ocena
0 / 5
Polubienia
1
Pobrania
6
Wydruki
1
Wyświetlenia
40
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Computers
Licencja
Creative Commons — Attribution — Share Alike

***** UPDATED to V2  ***** 
*****************************
Fixed the mirror issues. 
*****************************
Why I built this

The Tesla P40, P100 and M40 are passive cards. They were designed for server chassis with a wall of high pressure fans behind them. Put one in a workstation or a tower and it cooks itself.

I wanted a clean 40mm fan shroud that bolts to the end of the card, and I wanted versions for cards stacked back to back. I run two P40s in a Dell workstation and I'm building a four card box on an ASUS Z9PE-D8 WS, so the multi card versions were the whole point.

Everything is built from one OpenSCAD file, so you can change any dimension and regenerate.

What's included

File

What it is

Print qty

shroud_only

Single card shroud with 40mm fan socket

1 per card (single setup)

frame_only

Flat frame that screws to the card end. Used by every version.

1 per card

shroud_2card

Ganged shroud for 2 cards

1

shroud_3card

Ganged shroud for 3 cards

1

shroud_4card

Ganged shroud for 4 cards

1

tesla_40mm_shroud.scad
tesla_40mm_shroud_multi.scad

Parametric source for the single and multi card versions

n/a

STL and 3MF are both included. The 3MFs are already in print orientation. Bambu Studio will say "invalid config, load geometry data only" when you open them. Click OK; that just means there are no printer settings baked in.

How it works

It's two parts. A flat 4mm frame screws to the end of the card with three M3 screws. The shroud then bolts onto the frame with two M3 screws into captive nuts. The frame has counterbores for the screw heads and the shroud has relief pockets over them, so everything sits flat.

The card interface is measured from an existing Tesla duct design, not guessed. The outlet opening is 91 x 17.5mm, the three screw holes are on an 18mm pitch, and there's a 19mm notch for the 8-pin power connector.

Multi card versions

These are built for 2-slot spacing (40.64mm card to card). That's cards sitting back to back, like a Dell workstation with adjacent slots, or a board like the Z9PE-D8 WS using slots 1, 3, 5 and 7.

A 40mm fan socket is wider than 40.64mm once you add walls, so you can't just put four single shrouds side by side. The ganged shroud puts all the fans in one block with shared walls and shifts it to one side. Each card still gets its own sealed duct and its own fan. Shifting the fans opens a tunnel for each card's 8-pin plug, so the power cable runs straight out the back instead of getting trapped between ducts.

If your cards are on 3-slot spacing (60.96mm), you don't need the ganged version. Single shrouds fit side by side.

Hardware

  • Per card: 3 x M3 screws to mount the frame to the card end

  • Per card: 2 x M3 screws and 2 x M3 nuts to hold the shroud to the frame

  • One 40 x 40 x 28mm fan per card (see below)

Which fan

Static pressure matters more than airflow here. The P40 fin stack is long and dense, and a thin quiet fan barely moves air through it. Use a 40 x 28mm server fan. These are the numbers from the datasheets at 12V:

Fan

RPM

Airflow

Static pressure

Noise

Current

Delta FFB0412UHN

18,500

27.1 CFM

2.11 inH2O

58.5 dBA

0.65 A

Delta FFB0412EHN

14,500

20.3 CFM

1.23 inH2O

53.0 dBA

0.33 A

Sunon PMD1204PQBX-A

13,000

23.5 CFM

1.15 inH2O

51.5 dBA

0.57 A

My pick for a P40 under sustained load is the FFB0412UHN. It's loud at full speed, so get a 4-wire PWM version and let a fan curve keep it quiet at idle. The Sunon or the EHN are fine for P100s or power limited P40s.

The cards can't control these fans. Run them from a motherboard header or a SATA powered PWM hub, and drive the speed from GPU temperature with a script reading nvidia-smi or with the board's fan curve. Mount the fan so the airflow arrow points toward the card.

Print settings

  • PETG or ASA. The end of a P40 gets hot enough to soften PLA over time.

  • 0.2mm layers, 4 walls, 15 to 20% gyroid

  • No supports. The shroud prints outlet flange down and every overhang is under about 35 degrees. The frame prints flat.

Footprints: the single shroud is 110 x 44mm and 67mm tall. The 4 card shroud is 110 x 172mm, which fits X1, P1 and A1 beds but not the A1 mini.

Install

  1. Screw a frame onto the end of each card with three M3 screws.

  2. Multi card versions only: feed each power cable through its tunnel and plug it into the card.

  3. Push the fans into their sockets.

  4. Set the shroud on the frames and bolt it down through the ears.

Customizing

Open the .scad file in OpenSCAD. The variables you're most likely to touch are at the top:

  • N and card_pitch set the card count and slot spacing in the multi card file

  • conn_len, conn_h and conn_gap size the clearance for the 8-pin plug

  • mirror_card flips the screws and connector notch to the other side

  • socket_depth and fan_clear tune the fan fit

openscad -D 'PART="shroud"' -o shroud.stl tesla_40mm_shroud.scad
openscad -D 'PART="frame"' -o frame.stl tesla_40mm_shroud.scad
openscad -D N=3 -o shroud_3card.stl tesla_40mm_shroud_multi.scad

Status

This is v1. The card screw pattern, opening and connector notch come from measured geometry. The 8-pin plug clearance is still an estimate, so if you're printing the 4 card version, print a 2 card first and push a real plug and cable through the tunnel. If you print it and something's off, leave a comment with your card and what you measured and I'll update the files.

Tagi